Search:

Type: Posts; User: Frank Pratt; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    4
    Views
    137

    Be sure to thoroughly rough up the surface with...

    Be sure to thoroughly rough up the surface with something like 40 grit sandpaper. The epoxy will need lots of tooth.
  2. Replies
    6
    Views
    228

    I've done 3 wood countertops with under mount...

    I've done 3 wood countertops with under mount sinks. For all 3, I used clear, low viscosity epoxy on the sink cut out edges & underside where the sink attaches.

    One counter was finished with a...
  3. I got the wireless remote with mine & keep it...

    I got the wireless remote with mine & keep it clipped to my apron. It's always right where I need it.
  4. Replies
    50
    Views
    3,416

    What Glenn really needs to do is remove that...

    What Glenn really needs to do is remove that blocking, take over to the router table & use a round over bit to ease & beautify those hole edges. Couple of coats of Arm-R-Seal, put it back in, and be...
  5. Replies
    24
    Views
    1,730

    Thanks Aaron, I might just give them a call.

    Thanks Aaron, I might just give them a call.
  6. Replies
    24
    Views
    1,730

    I had that very thought as I was posting it. I'm...

    I had that very thought as I was posting it. I'm going to do one & laminate it.
  7. Replies
    24
    Views
    1,730

    I think it would be a good thing if they'd ...

    I think it would be a good thing if they'd provide a quick reference label that could be applied to a convenient surface. 'Cause ya, who wants to keep pulling out the manual.
  8. Replies
    50
    Views
    3,416

    Glenn, what sealant are you using? Some are so...

    Glenn, what sealant are you using? Some are so soft that just walking on a dirty floor can force gunk into the sealant.
  9. Replies
    16
    Views
    764

    I've had issues with Thompson's. If applied thick...

    I've had issues with Thompson's. If applied thick enough to provide more than a few weeks of protection, then it leaves a sticky, waxy film that does indeed attract dirt. If applied thin enough to...
  10. Replies
    28
    Views
    1,503

    Lee Valley used to have a very good selection of...

    Lee Valley used to have a very good selection of screws, including Spax. They still do carry these.
    ...
  11. Replies
    27
    Views
    1,203

    Thinning epoxy has serious implications for the...

    Thinning epoxy has serious implications for the strength of the joint. Check with the manufacturer, but even using solvents that they recommend will weaken the epoxy.
  12. Replies
    27
    Views
    1,203

    No, it is not an overstatement at all. I've been...

    No, it is not an overstatement at all. I've been there. If the cutting board sets in a puddle, or someone unknowingly puts it in a sink of water for a few minutes, it will be the beginning of the end...
  13. Replies
    27
    Views
    1,203

    But "regular white glue" has almost no moisture...

    But "regular white glue" has almost no moisture resistance & the board will begin to fall apart in a hurry.
  14. Replies
    33
    Views
    2,022

    Definitely a Saab.

    Definitely a Saab.
  15. Replies
    24
    Views
    1,730

    Ya, I get that. Sometimes you need to have a...

    Ya, I get that. Sometimes you need to have a voice conversation so both sides understand the meaning. I've had 2 or 3 calls to support with questions & they've been very good. The people I spoke with...
  16. I built an MDF box for dust collection & bit...

    I built an MDF box for dust collection & bit clearance that drops & locks over my table saw fence. It's a pretty basic fence, but does what I need it to. And with dust collection in the fence & below...
  17. Replies
    24
    Views
    1,730

    Besides the quality of the saw, the SawStop...

    Besides the quality of the saw, the SawStop manuals are very good as well. Easy to read, easy to understand, and thorough. If the manual can't answer your question, then they have very good tech...
  18. Replies
    33
    Views
    2,022

    I agree with what your trying to accomplish Kev...

    I agree with what your trying to accomplish Kev and good on ya. If he goes to prison there's really no chance he'll get rehabilitated.
  19. Replies
    24
    Views
    1,730

    You should definitely read the manual. Lots of...

    You should definitely read the manual. Lots of good info in there.
  20. Nobody uses lead for sound attenuation anymore. A...

    Nobody uses lead for sound attenuation anymore. A couple of layers of 5/8 drywall with Greenglue between works great. Before building something like this it's best to just dive down the rabbit hole &...
  21. Replies
    22
    Views
    1,291

    I have a Flexzilla hose & reel hung from the...

    I have a Flexzilla hose & reel hung from the ceiling. Not expensive & it works great. About the only complaint I have is that the put about 5 or 10' of too much hose in it so I have to pay attention...
  22. Replies
    40
    Views
    3,535

    There are no links or anything to indicate there...

    There are no links or anything to indicate there should be pics that I can see in those posts.
  23. Replies
    24
    Views
    1,282

    Startup current on induction motors is commonly...

    Startup current on induction motors is commonly 10X FLA. If you put a good meter on it, I bet you'd see that it draws a lot more than 90A
  24. That's basically what a couple of restoration...

    That's basically what a couple of restoration guys told me, but they said for some reason it just doesn't work in many cases. Probably has to do with the amount of stinky stuff that has built up on...
  25. Replies
    40
    Views
    1,961

    HD came to Canada several years before Lowes and...

    HD came to Canada several years before Lowes and for the most part, they have built near a HD, so they're both easy to get to. I tried, but I just can't like Lowes. Selection is generally not as...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4