Search:

Type: Posts; User: Paul Tubergen; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    44
    Views
    5,730

    I picked up a similar machine ‘68. Great tool. I...

    I picked up a similar machine ‘68. Great tool. I found a used rotary phase converter on eBay… some 30amp plugs (single and 3 phase) and cord and it was up and running. I think I have about 200-250...
  2. Replies
    20
    Views
    2,270

    As I recall fine woodworking had an article on...

    As I recall fine woodworking had an article on cleaning and tuning several years back. While I never needed to do the full cleaning etc they showed lifting the table all the way off (2 people) but it...
  3. Replies
    20
    Views
    2,270

    There was a set screw on the inside of the base...

    There was a set screw on the inside of the base on mine. There is a notch you can feel on the motor side where the rod goes on to the trunnion. If I recall it was as a 4 or 5 mm set screw.
  4. Replies
    25
    Views
    3,579

    I have used a router sled (like for flattening a...

    I have used a router sled (like for flattening a slab but smaller) followed by a sander. It worked fairly well.
  5. Replies
    25
    Views
    5,697

    Email sent

    Email sent
  6. Replies
    25
    Views
    5,697

    not sure - you may need to have more posts - can...

    not sure - you may need to have more posts - can you provide an email? We are moving over the next months to west Michigan and will be going by in the next few weeks... I would like to send some...
  7. Replies
    25
    Views
    5,697

    Can you PM me. I will be driving thru the area in...

    Can you PM me. I will be driving thru the area in the near future and could bring it with me. I will give more details then in a PM or via email
  8. Replies
    25
    Views
    5,697

    Where are you located? I have a 3hp single phase...

    Where are you located? I have a 3hp single phase that I would be willing to part with... it would be heavy to ship
  9. Replies
    25
    Views
    2,734

    There is a pretty good description in Grizzly’s...

    There is a pretty good description in Grizzly’s manual on line.
  10. NMP may work if lacquer thinned doesn’t.

    NMP may work if lacquer thinned doesn’t.
  11. I replace mine about 3 mos ago. I just replaced...

    I replace mine about 3 mos ago. I just replaced it with the new capacitor by attaching the same color leads to where the original was attached. As I recall the Capacitor had brown and blue wires like...
  12. Replies
    11
    Views
    4,049

    FWIW the 18 minimax has crowned wheels and sets...

    FWIW the 18 minimax has crowned wheels and sets up differently from the MM series saws.
  13. Replies
    33
    Views
    3,894

    I have used the poplar. Machines well (like...

    I have used the poplar. Machines well (like poplar). Many of the characteristics carry over but it is dark thru and thru. I used it for a bunch of picture frames...
  14. Had a 3 hp on a 20 amp and never tripped. Had...

    Had a 3 hp on a 20 amp and never tripped. Had severl years in an unheated garage in Michigan... it may be a bad breaker...
  15. Replies
    6
    Views
    1,291

    I had a lumpy belt that caused vibration....

    I had a lumpy belt that caused vibration. Switched to a twist lock after several years and the problem went away.
  16. See if your local lumber supplier sells scaffold...

    See if your local lumber supplier sells scaffold grade fir. It is pricey but clear.
  17. Replies
    6
    Views
    1,345

    Rough cut (fine working version) has a sled...

    Rough cut (fine working version) has a sled mounted on the slider so you can cut on either side of the blade... for what it’s worth.
  18. Replies
    3
    Views
    773

    My S45 has crowned wheels so I usually center on...

    My S45 has crowned wheels so I usually center on the top wheel. I tried with the teeth hanging over and did not get good results while re-sawing. There is a link to a good bandsaw set up in the...
  19. Replies
    35
    Views
    6,739

    I have the 18” mm saw and think it’s a very good...

    I have the 18” mm saw and think it’s a very good machine. It was manufactured by MIni Max, I believe their other saws (MM line) are produced by someone else. The machine is intended for furniture...
  20. Replies
    16
    Views
    2,113

    When you asked about rings - were they supposed...

    When you asked about rings - were they supposed to go between the flange and the blade? I recently bought a hammer and there were two rings that came with the machine of different thickness. I was...
  21. Replies
    39
    Views
    5,961

    I had a Vega for years. Good fence and I really...

    I had a Vega for years. Good fence and I really liked the finger saver for pushing thru narrow stock
  22. Replies
    54
    Views
    12,494

    I was hoping to see his new shop and the minimax...

    I was hoping to see his new shop and the minimax machines in use...
  23. Replies
    7
    Views
    1,534

    Mine is on the box that the wires run into on the...

    Mine is on the box that the wires run into on the motor.
  24. Yes, the scoring unit can only run with the 10”...

    Yes, the scoring unit can only run with the 10” blade.
  25. Replies
    29
    Views
    9,485

    I have used them in control rooms for process...

    I have used them in control rooms for process plants as a means to get wires into control equipment. The whole room typically has high heat load reducing the relative humidity and lots of air...
Results 1 to 25 of 27
Page 1 of 2 1 2