Search:

Type: Posts; User: Keith Harrell; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    3,405

    This is the wood I'm using

    This is the wood I'm using
  2. Replies
    9
    Views
    3,405

    I like the idea of a smaller square in the center...

    I like the idea of a smaller square in the center as movement would be limited and I would have a edge to miter off.
    I guess you are right about having a edge if I used the panel in the center...
  3. Replies
    9
    Views
    3,405

    Four sided rough end table

    I have some wood I'm going to use to build a table with and both my wife and I agree it needs to be a four sided rough edged table.
    I can only see two designs

    Picture frame miter joints edges...
  4. Thanks Ted I'll give them a look.

    Thanks Ted I'll give them a look.
  5. Looking for ideas for a patio table and bench seats using some spalted maple I found

    I would like some ideas on using 7 12'x15"x2" spalted maple planks. These are still rough sawn without the bark on the edges.
    I'm not sure about the legs mostly and should I use the maple or find...
  6. Replies
    3
    Views
    891

    I have a PDF if you still need it just PM me.

    I have a PDF if you still need it just PM me.
  7. Replies
    12
    Views
    2,482

    I built one that plywood and about 2 feet tall...

    I built one that plywood and about 2 feet tall and 2 feet wide. It has two 40 watt lights hooked up to a temp senser that turns on at 38 degrees and off at 45 degrees I think. They are sold at lowes...
  8. Warped 52-in Biesemeyer Fence Table Board

    I have noticed my 52 " Biesemeyer fence table has a sag in the middle. It's down about 1/8" in the middle. I have loosed all the screws along the rail and even drilled a couple new holes. I could...
  9. Tung Oil on white pine ?? to get that yellow golden old log cabin look

    I have been helping a friend build a small book case out of borg white common pine. The book case will be in a log cabin so he wanted the light wood look with knots. The logs are from up north and...
  10. I started with the 150/3 and ct22 and just added...

    I started with the 150/3 and ct22 and just added the Rotex to get boards flat faster. The 150/3 is by far easier to handle but also takes time to remove material. It's my go to sander 80% of the time...
  11. Replies
    1
    Views
    1,590

    Bandsaw fence for Rikon 10-345

    I'm looking for a replacement fence for my Rikon BS. The Kreg looked good but required me to drill two holes in the table and would have to be removed each time I changed blades.
    Thanks
  12. I have a dewalt 735 planner and would like to put...

    I have a dewalt 735 planner and would like to put a jet 12 disc sander on the other side if possible. Does anyone see any issues(weight) with doing this. I don't have the disc sander yet as I need to...
  13. Replies
    40
    Views
    13,384

    My first one required a belt sander to get flat....

    My first one required a belt sander to get flat. I learn quickly to pay more attention in the glueing up of the board.
  14. Replies
    4
    Views
    2,409

    Yes exactly the same. That's why I edited my post...

    Yes exactly the same. That's why I edited my post to reflect the faint white lines. I think the dust get trapped in the open grain or at least on mine it did.
    The only other problem I had which was...
  15. Replies
    4
    Views
    2,409

    I used it on my last project and it mills and...

    I used it on my last project and it mills and sands great. The only issue would be it's a little darker and my be more open grain than American walnut so I just some tung oil. You are right on the...
  16. Replies
    11
    Views
    4,360

    I assume the lower abranet grids are good also...

    I assume the lower abranet grids are good also like the 80. I received some 220 this week
  17. Replies
    11
    Views
    4,360

    Thanks for the suggestions. I have been using...

    Thanks for the suggestions. I have been using rubin for work under 220 and brilliant for 220 and above. I just received some Abranet discs so I give them a try along with the other suggestions....
  18. Replies
    11
    Views
    4,360

    Festool Sanding Paper worth it

    No this is not another sander flame off
    I have had a Festool 150/3 and a Rotex sander which I have used for years and have always used Festool paper. I have started to notice posts about others...
  19. Replies
    26
    Views
    3,550

    I have made two so far. One was with curly cherry...

    I have made two so far. One was with curly cherry and the other was walnut. If budget is a factor than I would think walnut should win in price. If I could make a suggestion.
    Walnut and make the...
  20. Replies
    12
    Views
    2,190

    I have to agree with no stickers needed for true...

    I have to agree with no stickers needed for true dried wood. The reason I say true is I got a similar deal when i was starting out years ago but he did not have use stickers when he dried it. I...
  21. Replies
    31
    Views
    5,259

    Steve, I have tired the bucket with water but the...

    Steve, I have tired the bucket with water but the antifreeze is a new a great idea.
  22. Replies
    31
    Views
    5,259

    The problem with poison is that they may die and...

    The problem with poison is that they may die and you then you have to find them after a few days. Not fun.
    I use traps but only have had trouble with mice which attract snakes which bother me more....
  23. Replies
    14
    Views
    6,261

    More teeth can cause problems when cutting...

    More teeth can cause problems when cutting thicker boards as the blade gullets will fill and cause the blade to bind. I like 60 or 80 teeth blades.
  24. Replies
    41
    Views
    8,054

    I have a pocket knife and the blade is getting...

    I have a pocket knife and the blade is getting shorter all the time and has to be reground. It happens mostly when I use it on Philip screws
  25. Replies
    9
    Views
    2,691

    I have seen plans with the front and sides cut...

    I have seen plans with the front and sides cut down a inch or more and thought about doing it but I like the 1/2 inch better. That should prevent most fingers injuries unless it's a group effort. I...
Results 1 to 25 of 211
Page 1 of 9 1 2 3 4