Search:

Type: Posts; User: ChrisA Edwards; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    14
    Views
    903

    I think I would make a 3 sided jig that sits on...

    I think I would make a 3 sided jig that sits on the rail. A section of the jig would have reference fences/stops for a plunge router. A bit further down the jig would be a stop hole, where a spindle...
  2. Replies
    29
    Views
    2,170

    The 3HP upgrade kit included the gas strut, motor...

    The 3HP upgrade kit included the gas strut, motor and control box.
  3. Replies
    29
    Views
    2,170

    I did the upgrade from the PCS 1.75HP (110v) to...

    I did the upgrade from the PCS 1.75HP (110v) to the 3HP 220V upgrade. Cost around $600 a couple of years ago. Took about an hour to switch motors and put in the new control box.

    Saw doesn't...
  4. I used the Loc-Line on my PM719T ...

    I used the Loc-Line on my PM719T


    https://www.youtube.com/watch?v=jIJWNBAUtyk
  5. Replies
    8
    Views
    662

    Around that center piece, could you glue (screw?)...

    Around that center piece, could you glue (screw?) in a couple of sacrificial blocks to help support it while you plane and the later cut it out?
  6. Replies
    22
    Views
    1,417

    Not quite sure what a laser ruler is, but I have...

    Not quite sure what a laser ruler is, but I have one of these, Bosch Blaze GLM50C. It seems accurate to 10th's of a mm, but as it's handheld, there is operator error in keeping it still.

    I often...
  7. Replies
    6
    Views
    702

    Thank you, I've had similar experience with the...

    Thank you, I've had similar experience with the Klingspor, so so performance.

    When I ordered them, there were a couple of abrasive options available. I bought both, but really didn't see any...
  8. Replies
    14
    Views
    818

    Had the True position, plus an extension for...

    Had the True position, plus an extension for wider drawers, for a few years now.

    Works as advertised.

    Cool, simple, accurate, easy to use tool. Doesn't gets used very often, but does the job...
  9. Replies
    29
    Views
    3,100

    The reason I started this post was that this WP...

    The reason I started this post was that this WP tool offered the left right positioning of the stops for cutting mating pieces.

    I have a Pantorouter, and yes it can be setup and be manually...
  10. Replies
    29
    Views
    3,100

    Much appreciated.

    Much appreciated.
  11. Replies
    29
    Views
    3,100

    Perfect, thanks

    Perfect, thanks
  12. Replies
    29
    Views
    3,100

    Yes would love to see those pictures. I just...

    Yes would love to see those pictures.

    I just got a Onefinity CNC, so my first thought was to replicate the Woodpeckers idea, I actually have the old Woodpeckers drill press fence, after I upgraded...
  13. Replies
    29
    Views
    3,100

    Yes I own a Pantorouter. What this has that the...

    Yes I own a Pantorouter. What this has that the Pantorouter doesn't, at least currently, is the adjustable angle fence for 45 degrees or other non 90 degree joints and the ability to accurately set...
  14. Replies
    29
    Views
    3,100

    You took the thoughts right out of my head.

    You took the thoughts right out of my head.
  15. Replies
    29
    Views
    3,100

    Woodpeckers MortiseMatch

    Got the email flyer for this accessory this morning from Woodpeckers.

    Being a Festool Domino 500 user, this looked like an intriguing, useful jig.

    I watched the video, without looking at the...
  16. From the front of the fence to the end of the...

    From the front of the fence to the end of the rail is 43"

    https://hosting.photobucket.com/images/i452/cedwards874/SawstopFenceLength.jpg
  17. Replies
    27
    Views
    3,847

    Not sure if will help, but about 15 years ago, I...

    Not sure if will help, but about 15 years ago, I installed a 4 post car lift in the center bay of my garage. It could lift 9000lbs and go to a height of 6'6" all on 110v.

    I extended the lifts...
  18. I ordered the router table and installed that,...

    I ordered the router table and installed that, along with the Incra legs
  19. Where the LSTS Clamps is a long way away from the...

    Where the LSTS Clamps is a long way away from the blade. Without the front clamp, I can get about an 1/8" of movement at the fence. Sometimes I forget to clamp it and it rarely messes up my piece,...
  20. Have an Incra LSTS on my Sawstop for about 2-3...

    Have an Incra LSTS on my Sawstop for about 2-3 years. Love it.

    I like the ability to go to a specific setting, minutes, weeks, etc. after making a previous cut.

    I find it to be very accurate,...
  21. I have the TSO version, had it for about 4 years....

    I have the TSO version, had it for about 4 years.

    They look identical, other than the color.

    I do like the tool and use it a lot with my Festool tracks.
  22. Replies
    41
    Views
    3,861

    I just signed up a couple of months back. Had...

    I just signed up a couple of months back.

    Had to have a $20K out patient eye surgery about 3 weeks after starting Medicare.

    I have a plan D for prescriptions, through Aetna and a plan G...
  23. Replies
    30
    Views
    1,855

    That's super cool, would love to see a YT video...

    That's super cool, would love to see a YT video of the whole thing plus a list of components and sources if you would care to share.

    I can't tell from your photos, but do you think it would be...
  24. Replies
    19
    Views
    3,289

    He's just turned 29. Has a good steady job,...

    He's just turned 29. Has a good steady job, although is moving up the ranks faster than any other employee has done in a large nation wide company.

    This would be a side kick startup, with not a...
  25. Replies
    19
    Views
    3,289

    Yes, I wanted to say, he's never really used...

    Yes, I wanted to say, he's never really used woodworking or metal working machines, I was fortunate to do both for many years in high school, but he was great assembling Lego's.

    I used to love it...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4