Search:

Type: Posts; User: Andrew Hughes; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    20
    Views
    450

    My best guess is your sliding Dt that you cut in...

    My best guess is your sliding Dt that you cut in the top is too close to the edge. On your next one move it in and do change the grain on the male part quarter or rift.
    What wood am I seeing looks...
  2. Iíve used Eucalyptus and found it very difficult...

    Iíve used Eucalyptus and found it very difficult to machine. The stuff I used was Air dried and it still was a pain.
    I cannot imagine how difficult kiln dried would be.
    Turing it sounds like a...
  3. Replies
    9
    Views
    263

    Wow this one is killer . The first one is nice...

    Wow this one is killer . The first one is nice too but I like this one better.
    Great use of a single wide board.
  4. You should be able to manage all the parts. All...

    You should be able to manage all the parts.
    All metric sockets a good set of pliers screws drivers and crescent wench.
    Sounds like a good project to learn from. If you can get all back together...
  5. Replies
    21
    Views
    799

    I used a chain hoist mounted to the main header...

    I used a chain hoist mounted to the main header of my shop door.
    I lifted the my jointer up off the trailer then drove out the trailer.
    I have a 1900 # jointer.
    Chain hoist are pretty handy.
    ...
  6. Very nice bench Brad. I like it a lot

    Very nice bench Brad. I like it a lot
  7. Replies
    11
    Views
    547

    Ok I see what you mean. I donít know what the...

    Ok I see what you mean. I donít know what the rules are for that.
    I do remember a few instances when I had glue coming out of the pores of the wood. I asked myself I wonder if the domino is too...
  8. Replies
    11
    Views
    547

    Your post read like your going across the grain...

    Your post read like your going across the grain instead of long way with the grain.
    Sometimes when Iím questioning a jointery fit I will make up some pieces from scraps to test.
    Its good practice...
  9. Replies
    8
    Views
    222

    One indication that the Op might have soft...

    One indication that the Op might have soft service is do the light dim when the saw starts.
    This happened to me when I had 18 Laguna with a I think was a 3hp baldor motor. It was draw lots of amps...
  10. Nice piece Chris. Very good use of a wide slab....

    Nice piece Chris. Very good use of a wide slab.
    How did you join the case it looks like miters?
  11. One more reason I am reluctant to take a very...

    One more reason I am reluctant to take a very good blade is goofing up a tooth or two.
    My Aggi is kinda tight taking the blade out of the upright side of the saw.
    Ive done it enough to know what to...
  12. Thread: Aprons

    by Andrew Hughes
    Replies
    27
    Views
    1,528

    I donít wear a apron. Because I donít want to...

    I donít wear a apron. Because I donít want to look like one of those Utube dorks. Teaching how to make jigs and fixtures that no one really needs.:p
  13. Iím a lot like Chris when I get a new blade and...

    Iím a lot like Chris when I get a new blade and it cuts so nicely I wonít change it till itís dull. I had to seek my 14 inch bandsaw because the wood shop is out of money. Scraping the bottom :(
    Its...
  14. Replies
    1
    Views
    120

    Iím pretty good at setting up my Aggi B 20-20. I...

    Iím pretty good at setting up my Aggi B 20-20. I find a new blade solves most problems with my bandsaws.
    If it doesnít change Iíd be surprised.

    Good Luck ,Nice saw.
  15. Replies
    5
    Views
    313

    Looks good. I like it

    Looks good. I like it
  16. Replies
    21
    Views
    982

    Yes plan on clamping. When you add glue the...

    Yes plan on clamping.
    When you add glue the joints will probably need more then your hand pressure to close.
    I use dominos a lot I had the same thoughts as you.
    So donít mess this up your almost...
  17. I say yes it is possible. But you will need a...

    I say yes it is possible. But you will need a second reference surface bigger and flatter then the table your scraping.
    Plus youíll need more tools,time and skills you may not have.

    I hand...
  18. I like the look of the piece. I don't like the...

    I like the look of the piece. I don't like the evenly spaced dovetails. Looks to mechanical or machine made. I would like too see the number cut down to half random space. Or none at all.
    Good luck
  19. Excellent work Tom.

    Excellent work Tom.
  20. Replies
    15
    Views
    494

    Thatís a beauty Phil. Really like it.

    Thatís a beauty Phil. Really like it.
  21. Replies
    4
    Views
    281

    Look for cypress. True cedar wouldnít make a good...

    Look for cypress. True cedar wouldnít make a good tub.
    Everyone calls cypress cedar.
  22. Replies
    15
    Views
    736

    I was thinking about the same Fww article John...

    I was thinking about the same Fww article John mentions. The only advice I can add is do your best to have the right blade for the cut. Then less teeth and less time in the cut less heat.
    Trying to...
  23. Replies
    23
    Views
    1,105

    Iíve found some woods just cannot be hand planed...

    Iíve found some woods just cannot be hand planed after kiln dried.
    Kiln dried with knots doesnít sound like fun.

    Good Luck
  24. I recommend you don’t mess with the tables. If...

    I recommend you don’t mess with the tables.
    If they are coplaner to each other use your Oneway.
    I use a dial indicator thats held in a fixture to set knives in my 12 inch Oliver. My head is also...
  25. Replies
    20
    Views
    607

    Will the saw rip 45s on straight stock. To me...

    Will the saw rip 45s on straight stock.
    To me that would be my first guess.
    Other then that is has still be your set up or accurate milling of the piece your cutting. Impossible for anyone to know...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4