Search:

Type: Posts; User: Andrew Gibson; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    0
    Views
    572

    Blum Tip-on, Power of the push?

    I'm working on a credenza design and am planning to use Blum movento slides with Tip-on push to open. Does anyone out there have an experience with the different "push" strengths? I'm trying to...
  2. Replies
    6
    Views
    931

    I have had a 1k, 5k, 15k Shapton Pro stone set...

    I have had a 1k, 5k, 15k Shapton Pro stone set for years. I never strop. My sharping regiment is coarse/x coarse DMT duosharp for really rough work (and stone flattening), 1k for bevel. Straight to...
  3. I am always more excited about my Next project...

    I am always more excited about my Next project than my last. Of finished projects I think these are the ones I am most proud because they forced me to evolve.
    456762456763456764456765
  4. Replies
    21
    Views
    2,779

    In small diameter bits I would not get hung up on...

    In small diameter bits I would not get hung up on the shank size. Choose the shank that best suits your intended use. If you are likely to want to use the bit in your trim router, go 1/4". You can...
  5. Replies
    19
    Views
    2,688

    I would use Titebond 3, If I was really worried I...

    I would use Titebond 3, If I was really worried I would join the pieces with a 1/2" x 1/2" tongue and groove. This would add a massive amount of glue surface, mechanical strength, and add a...
  6. Remember, this is the cave, make sure to use your...

    Remember, this is the cave, make sure to use your egg beater or treadle Dremel. :D
  7. Hi Jim. That is odd to hear. I have been with...

    Hi Jim. That is odd to hear. I have been with Infinity 7 years now and both of our ripping blades should have had a true flat top grind in that time. Feel free to reach out to our customer service...
  8. If you have a tablesaw with an extension table...

    If you have a tablesaw with an extension table you could throw it in as a secondary router table. I have run into situations where having a second table can come in handy.
  9. Hi Jim, in all honesty I think we may have...

    Hi Jim, in all honesty I think we may have replaced one in all these years. It has just never been an issue. We rarely get asked about a guarantee. Jack always says he will take care of anyone that...
  10. The screws for the rear, The two pan heads that...

    The screws for the rear, The two pan heads that are actually part of the saw use a 5/16 allen key, all of the set screws in the Colliflowner insert use a 1/8" allen. If your planning to come by,...
  11. I see a few questions that I can help with. I...

    I see a few questions that I can help with. I have worked for Infinity now for 7 years as "Resident Woodworker"
    Infinity is not the manufacturer of the SawStop Insert. It was invented and is...
  12. Replies
    22
    Views
    2,247

    Try searching for a Moxon Vise. They have been...

    Try searching for a Moxon Vise. They have been gaining popularity with hand tool folks and the Roubo craze. There are all sorts of stuff out there from complete vises, to kits, to diy plans.
  13. Replies
    19
    Views
    3,758

    Good Point, I have not found a glue that I would...

    Good Point, I have not found a glue that I would trust without removing the finish if I needed more strength than screws alone.
  14. Replies
    19
    Views
    3,758

    My question is always what are you expecting the...

    My question is always what are you expecting the cabinet to sustain with glued plywood edges that it won't with pocket screws alone? If your cabinet gets hit by a Buick you have bigger issues. I...
  15. Replies
    20
    Views
    2,261

    When I started building instruments I learned...

    When I started building instruments I learned quickly to was my hands religiously. I started washing hands between each operation. There is nothing worse than tryin to sand dirty fingerprints out of...
  16. Replies
    21
    Views
    2,110

    Haha, none taken. I could follow that with the...

    Haha, none taken. I could follow that with the fact that they got in big trouble. They both got summer school and lots of extra chores on the farm after the initial punishment.
  17. Replies
    21
    Views
    2,110

    I have uncles that are identical twins, one is...

    I have uncles that are identical twins, one is right handed and the other left handed. They used to get put in different classes in school so they wouldn't cause trouble. They figured out that they...
  18. The only wood I have ever seen that has those...

    The only wood I have ever seen that has those little light color splotches like in pic 3 and 4 is poplar. The color and medullary ray pattern in the first pic also look like poplar to me. I vote...
  19. Hi Ron, I have used the Triton 2.25 with the Mega...

    Hi Ron, I have used the Triton 2.25 with the Mega Dado quite a bit and have no issue recommending the combo. Regardless of the router itself I always recommend a 50% (1") wide pass at a maximum of...
  20. Replies
    13
    Views
    3,578

    Welcome to the Creek John! If you have any...

    Welcome to the Creek John!
    If you have any questions about the Infinity table please feel free to reach out to me directly. I won't post my opinion here because I am a little bias.
  21. Replies
    121
    Views
    12,496

    When I started building acoustic instruments I...

    When I started building acoustic instruments I learned very quickly you really have to be careful. An acoustic instrument has to be built strong enough to last a long time but also light enough to...
  22. If your starting from scratch here are some terms...

    If your starting from scratch here are some terms you should know.

    Board foot.
    This is how rough lumber is measured. One board foot is equal to a board 1" thick, 12" wide, and 12" long. A quick...
  23. Hi Clarence, where are you in Florida? There are...

    Hi Clarence, where are you in Florida? There are quite a few places you can find Sissoo Rosewood, the question is do you want it green or kiln dried? Also are you looking for lumber, slabs, or...
  24. I tend to use all three. When I start milling...

    I tend to use all three. When I start milling rough lumber for a project I will put a dedicated rip blade on the saw, as the project progresses to the point that I start needing to crosscut, I switch...
  25. The composition of the photo is also quite nice....

    The composition of the photo is also quite nice. Thanks for sharing!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4