Search:

Type: Posts; User: Kevin Jenness; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    6
    Views
    149

    I have a couple of Gast pumps, 522s I believe,...

    I have a couple of Gast pumps, 522s I believe, and they both have external felt filters that look like these internal ones...
  2. Replies
    16
    Views
    643

    A somewhat more sensitive gauge can be made with...

    A somewhat more sensitive gauge can be made with a button tipped dial indicator held in a wood block that straddles the knife pocket. Here's an excellent primer on adjusting traditional planers with...
  3. Replies
    16
    Views
    643

    Ask the manufacturer/ see if you can find a...

    Ask the manufacturer/ see if you can find a manual online. If the knives are in the head now and the machine feeds ok it is probably safe to copy the existing knife projection. If they are too far...
  4. Shims work up to the point that the slides start...

    Shims work up to the point that the slides start to bind due to the opening becoming too small. Side mount slides usually call for a gap of -0"/+ 1/32" per side. You can taper the front of the drawer...
  5. Replies
    36
    Views
    1,088

    First "real" snow here in VT - 10" of powder here...

    First "real" snow here in VT - 10" of powder here in the valley, 18" reported at Mad River Glen. Headed back down below zero tonight. I feel bad for folks in the south who aren't set up for snow and...
  6. Replies
    23
    Views
    1,398

    I didn't. I have a setup from...

    I didn't. I have a setup from http://www.wnysupply.com/index.html, basically a static convertor to get the "generator" motor spinning. I did check the third leg voltage when I set it up but have...
  7. Replies
    10
    Views
    627

    What mistakes have been made that I can learn...

    What mistakes have been made that I can learn from the experiences of others before I do them again? What mistakes am I doomed to make on my own regardless of your various remonstrations?


    I'll...
  8. I used red Loctite once by mistake and was able...

    I used red Loctite once by mistake and was able to weaken the bond with heat. The same goes for most epoxies.
  9. There's this...

    There's this https://www.autogeek.net/griots-orbital-polisher.html# and this...
  10. Replies
    51
    Views
    1,684

    I've had a Mitutoyo analog model for about 40...

    I've had a Mitutoyo analog model for about 40 years, it still works fine. .001" grads, the dial rotates to set zero. Sorry, don't have a model #. A button tip is more useful for knife setting than a...
  11. From an old thread on customer service...

    From an old thread on customer service https://sawmillcreek.org/showthread.php?235588-What-is-your-experience-with-quot-euro-machine-quot-customer-service...
  12. Replies
    11
    Views
    525

    There are hundreds of resin formulations that can...

    There are hundreds of resin formulations that can be used for this application including polyester, epoxy and polyurethane. For small quantities you are probably best off going to a craft store and...
  13. Replies
    48
    Views
    7,237

    That's about 400 inches/minute, plenty fast for a...

    That's about 400 inches/minute, plenty fast for a machine like that.
  14. At 5.5" I can't see a problem as long as the mc...

    At 5.5" I can't see a problem as long as the mc is the same. Thinner means less potential for issues and more yield. Do both sides for balance.
  15. Be aware that the stated shelf life is one year...

    Be aware that the stated shelf life is one year unopened and eight months after opening. As I recall the same was true for the Weldwood product, although your experience with it indicates that it...
  16. Replies
    5
    Views
    486

    Watch out for splinters and avoid sanding dust....

    Watch out for splinters and avoid sanding dust. Some people are allergic.
  17. Replies
    4
    Views
    284

    There's this (I have not used it)...

    There's this (I have not used it) https://www.systemthree.com/products/cold-cure-cold-weather-epoxy

    A general approach to epoxy in cold temps from West System...
  18. Replies
    29
    Views
    1,701

    I am definitely considering upgrading my shop...

    I am definitely considering upgrading my shop attire.
  19. The only thing the manual states about the...

    The only thing the manual states about the infeed/outfeed is that the outfeed table is set by the factory precisely and should not be adjusted.

    I checked this several more times with a couple of...
  20. It's not clear what you mean by "sagging" or...

    It's not clear what you mean by "sagging" or exactly what your test procedure is. I am guessing that you are resting your straightedge on the outfeed table and measuring the gap between it and the...
  21. Replies
    16
    Views
    860

    It's hard to know from your description whether...

    It's hard to know from your description whether the problem is inaccurate joints, clamping technique or change in moisture content. A dry run in clamps using a straightedge would tell you a lot. If...
  22. Replies
    29
    Views
    1,701

    Isn't that something? The best woodworkers have a...

    Isn't that something? The best woodworkers have a way of making it look so easy.
  23. Replies
    8
    Views
    466

    Don't you need a removable dust trap at one end?

    Don't you need a removable dust trap at one end?
  24. Replies
    35
    Views
    3,407

    What is the relative cost of Nordfab pipe and...

    What is the relative cost of Nordfab pipe and fittings to similar gauge spiral pipe? Is there a major decrease in installation time? I recognize the ease of reconfiguration, but is there a good...
  25. I prefer Titebond Extend over original for veneer...

    I prefer Titebond Extend over original for veneer as it has a more rigid glueline. I also use epoxy and Titebond 2 at times. I did use Titebond original on 1/16" veneer on a number of projects with...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4