If you start your saw with the tension releases, it will usually ruin the blade.
Type: Posts; User: Dane Riley; Keyword(s):
If you start your saw with the tension releases, it will usually ruin the blade.
I've replace spatula handles with turned walnut finished with walnut oil. These have been through the dishwasher hundreds of times. They get dull, but reapply walnut oil and they look like new. And...
And that's with a Monroe hollower.
Deep hollowing with and armbrace is a good way to dislocate your shoulder. I came close. I won't use my armbrace for long over the tool rest or with a curved tool. You need a captive hollowing system.
The O rings are snug. I do have a holder to hold the hose and provide a bit of pressure to keep it from falling out.
Second this. I made mine with a brass fitting and cut some groves for O rings392235
You need a bleed valve to position the turning and a gauge to set the bleed valve. A filter is a good idea to prevent dust from being sucked into the pump.
John, next time you photograph in your shop, could you photograph your spindle gouge grinds and start a new thread? I know what a many versions of a bowl gouge grind looks like, but have seen few...
My cross feed drill vise had way to much play to work for threading. When I saw this video I tried to readjust mine. One axis was fine already, the other one would not turn with a reasonable amount...
Some of the prettiest of turnings come from the ugliest of logs. And that log is ugly.
This looks good for a tall hollowform.
I have a piece of aluminum that sits between the bed ways. This maintains the Y axis position and the square alignment. Notice the twist mark that reminds me which way to take up the small amount of...
Yes. It was so tall I needed the steadyrest, usually I don't.
The Y slide is some sort of extrusion I found at the local scrapyard. I lock it with the screws at all four corners. I went to a lot...
ok
390462390463390464
It is 1.25 x 8, so the chuck threads directly on. When Enco was around it was not expensive with a 20%o ff and free shipping. That may be why they got bought out.
The wood blocks with screws that...
There can't be any play anywhere. I suspect you will need to lock the dovetail with locking screws tapped in the sides.390381
The play on the threaded rod must also be eliminated. Mine has...
I fit that, and I'm in Forestville This weekend is out, but next week is possible.
If you go to Wine country Woodturners, You've seen if not talked to me. I'm bad with names in my old age. Hard...
Tool rest height is also involved. If the spindle height is higher, try dropping the tool rest slightly (in relation to the spindle) so the tool is not level but the handle is lower. The cutting...
One thing I've wondered about is if the alignment is off is it because the tailstock is cocked(skewed) or offset? It could line up perfectly if the two errors were opposite. One way to check for this...
A PVC "T" for sprinkler risers (side hole is NPT threaded) stuffed with cotton works well.
All my large apple trees are hollow. Some just have crescent shaped trunks. Still produce lots of apples.
Huh? You don't change jaws? Or does the non permanent locktite release easily?
369987Largest Diameter .85"
7 teeth
30 deg angle where engages.
13 Deg on upper part
$50 for no chuck key and no jaws is a ripoff, IMHO. That said, I like the chuck, although the precision is...
Not rolling, but could easily be made so.
4(Qty.) 1.5" x 1.5" x 17" legs with 3 notches cut in each leg. 3(Qty.) .75" x 11.5" x 18" , each with a 3/4" deep and 1.5" wide notch on each side,...
Denatured alcohol dissolves wax. I would think you could remove enough with this to allow adhesion of another finish. Anyone ever tried this? How much did you have to wipe it to get adhesion?
Could you enlighten us on how to "sun treat" flaxseed oil?