Search:

Type: Posts; User: Jon Snider; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    20
    Views
    836

    I too have 200 amps to my shop and when my 3...

    I too have 200 amps to my shop and when my 3 phase idler is on plus DC and table saw, plus someone else on the planer or jointer, I’m glad to have it. I have plenty of reserve right now but might...
  2. Replies
    105
    Views
    11,353

    Try your local lumber yard for T1-11. Plus if...

    Try your local lumber yard for T1-11. Plus if they have it you might get a better price plus free delivery to the job site. Also look at Smartside 7/16”. It’s what I used and I got a price at my yard...
  3. Replies
    22
    Views
    2,085

    do you have a part number for the riving knife...

    do you have a part number for the riving knife that fits? K700S

    thx.
  4. After reading this, almost indispensable, right? ...

    After reading this, almost indispensable, right? I use mine frequently in building boats.

    I’m often reminded of the oscillating saws to remove plater casts, the ones you can push (gently)...
  5. Replies
    120
    Views
    12,929

    Some pics of my K700S after finally getting it...

    Some pics of my K700S after finally getting it all set up and cutting wood. I’m not sure if I will use, or leave on, the short crosscut fence. Any advice here?


    412158412159412160

    A pic of the...
  6. Replies
    120
    Views
    12,929

    The receiver for the remote is inside of the box...

    The receiver for the remote is inside of the box on the basement wall. The remote works fine through the floor for me. Clearvue gave me some distance I canít remember but it was longer than my shop...
  7. Replies
    120
    Views
    12,929

    Spent a couple of hours in the basement setting...

    Spent a couple of hours in the basement setting up the main trunk dust collection trunk from the Clearvue. I used a 6” Fernco coupler b/w the plastic intake and the first piece of metal pipe, plus...
  8. Replies
    26
    Views
    2,028

    Marty, I’m reading this that your box material...

    Marty, I’m reading this that your box material is MDF and you have a single layer (plus laminate) of HDF, and your quick clamps are Festool. Correct?

    Where did you find 3/4 HDF? Having no luck...
  9. Replies
    26
    Views
    2,028

    Thanks Tom. Since the Parf Mk2 is now back in...

    Thanks Tom.

    Since the Parf Mk2 is now back in stock itís time to fish or cut bait. It seems the choice of top comes down to holes for clamping vs. use with track saw. The way Iím understanding...
  10. Replies
    9
    Views
    721

    Thanks Tom. Blade is 5.5 feet from wall where it...

    Thanks Tom. Blade is 5.5 feet from wall where it sits right now so I’m plenty good, if I keep it there, for sheet goods. If I need to cut a 12’ board in half I’ll just use my chop saw.
  11. Replies
    9
    Views
    721

    Thx Jack and James. And thanks once again Jim for...

    Thx Jack and James. And thanks once again Jim for all the frequent great advice.
  12. Replies
    19
    Views
    1,479

    You might get into 2015 with that! :)

    You might get into 2015 with that! :)
  13. Replies
    19
    Views
    1,479

    Eliot, There are numerous shop build threads...

    Eliot,

    There are numerous shop build threads in this sub forum. Many of them are focused on smaller shops, often limited by a garage size etc. For my recent build, and thread, I went through...
  14. Replies
    105
    Views
    11,353

    Actually seems like a lot. Looking good Thomas.

    Actually seems like a lot. Looking good Thomas.
  15. Replies
    9
    Views
    721

    Table Saw location in shop

    Fellow Creekers,


    I'd greatly appreciate some late advice on locating my sliding table saw w/ 10' table. Late b/c I'm putting together cyclone and will start on ductwork soon. Early on I was...
  16. Replies
    26
    Views
    2,028

    thanks Robert. Since you’re going w Festool...

    thanks Robert. Since you’re going w Festool clamps, your top will be 3/4”?

    what is the polyurethane / mineral spirit/ turp recipe? I’ve used one called boat soup for gunwales, etc which is 1:1:1...
  17. Replies
    120
    Views
    12,929

    Ruby, the MBS shop dog, is psyched. 410962

    Ruby, the MBS shop dog, is psyched.

    410962
  18. Replies
    120
    Views
    12,929

    Finished setting up the Rinnai EX38CT heater, gas...

    Finished setting up the Rinnai EX38CT heater, gas hook up, and connecting the Honeywell thermostat to the wireless network. I chose this thermostat since it was the only one I could find which worked...
  19. Replies
    26
    Views
    2,028

    Oh lord, I didn’t need to see that... Wonder...

    Oh lord, I didn’t need to see that...

    Wonder if you could mount it on Zambus casters?
  20. Replies
    6
    Views
    537

    Jim, I’m sorry but I just don’t follow you. I do...

    Jim, I’m sorry but I just don’t follow you. I do appreciate your many very helpful posts but I’m perhaps too slow to get this one.

    Jamie, I’ll definitely have lots of support below, but since...
  21. Replies
    6
    Views
    537

    DC duct work through floor tips

    Iíll be putting together some of the duct work from my Clearvue over the next week or so. Going slow to see how tools and duct layout evolves, as the original plan has already changed several times. ...
  22. Replies
    26
    Views
    2,028

    Thanks Todd. Was thinking about adding some to at...

    Thanks Todd. Was thinking about adding some to at least one edge, mainly for clamping.
  23. Replies
    105
    Views
    11,353

    +1. Your shop is gorgeous, the timber framing and...

    +1. Your shop is gorgeous, the timber framing and outdoor setting seems to me to call for more natural, simple colors, without the cross trim piece. My preference is slightly darker trim than wall...
  24. Replies
    26
    Views
    2,028

    Thanks Dick. That was exactly my concern. I...

    Thanks Dick. That was exactly my concern. I suppose I could build a double layer for the one half of the top without holes, and build some type of support, or maybe open torsion box, for the “MFT”...
  25. Replies
    26
    Views
    2,028

    Thanks too from me to all replies. Dan it looks...

    Thanks too from me to all replies. Dan it looks like you’ve shown several reasons such a top would be good for part of an assembly/utility table even without using the track saw functions.

    My top...
Results 1 to 25 of 239
Page 1 of 10 1 2 3 4