Search:

Type: Posts; User: Frank Drackman; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    1,434
    Views
    110,703

    Your knowledge and skills are amazing to see....

    Your knowledge and skills are amazing to see. This thread is inspiring.
  2. Replies
    16
    Views
    450

    Reformed Router Bit Snob

    In the past, I was a complete router bit snob. I would only purchase bits made from a few high-end manufacturers & if possible bit with a 1 shank. Then I was gifted a trim router that only used...
  3. Replies
    23
    Views
    811

    I'm the OP on this thread. I can assure you that...

    I'm the OP on this thread. I can assure you that I don't look for an excuse to complain about customer service. My last post about customer service was to praise Target Coatings for their...
  4. Replies
    39
    Views
    1,440

    No, they are used in the opposite order. One face...

    No, they are used in the opposite order. One face gets flattened on the jointer, then one edge so that it is flat & 90 degrees to the flattened face. Next to either the tablesaw to make the opposite...
  5. Replies
    23
    Views
    811

    Laguna Tools Customer Support

    I have to laugh at my recent interaction with Laguna Tools customer support.

    A few weeks ago the switch on my LT 18 bandsaw died. I tried calling them to discuss the problem but it wasn't during...
  6. Replies
    15
    Views
    602

    I would measure the thickness of the piece that...

    I would measure the thickness of the piece that you want to put the profile on. Next get a round over bit, with bearing, that is 1/2 of the thickness. Since you can't use a router table use a...
  7. Replies
    9
    Views
    448

    I wasn't kidding at all. I knew that I was...

    I wasn't kidding at all. I knew that I was missing something with the price. That is why I asked.
  8. Replies
    9
    Views
    448

    I forgot about the vacuum system. That is a big...

    I forgot about the vacuum system. That is a big add-on.
  9. Replies
    9
    Views
    448

    $32K used 2018. What am I missing? Same model...

    $32K used 2018. What am I missing? Same model with ATC is $36,795 new at the Shop Sabre site.
  10. I have an extra Dewalt 12" compound miter saw & a...

    I have an extra Dewalt 12" compound miter saw & a Bosch jobsite tablesaw on mobile stands that I keep just to loan out. I can't count the number of decks, stairs, etc that have been built with them....
  11. I asked this question a few months ago and many...

    I asked this question a few months ago and many memebers responded that they did without any issues.
  12. Replies
    7
    Views
    273

    I tried the upside down trick with zero luck. ...

    I tried the upside down trick with zero luck. The saw is over twenty years old and this is the first issue so I'm fine with replacing the switch.
  13. Replies
    7
    Views
    273

    Exactly. It was the first thing that I tried but...

    Exactly. It was the first thing that I tried but was concerned about breaking it. The more I investigated I realized that it had to be the clip so I applied a little more force and it popped right...
  14. Replies
    7
    Views
    273

    Please disregard.I found how to remove from...

    Please disregard.I found how to remove from housing.
  15. Replies
    7
    Views
    273

    Help Removing Switch From Housing

    The switch on my Laguna LT18 bandsaw finally died. I tried blowing it out without any success. I ordered a new part but need some help replacing it. Attached is a picture of the switch in the...
  16. Replies
    16
    Views
    880

    If you want the cherry to age to a darker color...

    If you want the cherry to age to a darker color make sure that your clear coat doesn't have UV inhibitor in the formula.
  17. The Ereplacement website says that it is...

    The Ereplacement website says that it is compatible with your unit. See attached screen shot.

    424653
  18. I installed the vortex cone upgrade kit on my...

    I installed the vortex cone upgrade kit on my dust collector one week ago and I'm extremely impressed. My system started as a 3hp Penn State Industries two bag collector that I swapped the bags for a...
  19. Replies
    5
    Views
    440

    If you are going to color the wood I would...

    If you are going to color the wood I would investigate dyes instead of stains. I find the dyes give me much more control of the color especially in end grain.
  20. Replies
    12
    Views
    427

    I have a different brand. The best way I have...

    I have a different brand. The best way I have found to make sure that the drum is parallel is to use two 1-2-3 setup blocks with no sandpaper attached. The 2" works best for me. One on the inboard...
  21. Replies
    17
    Views
    1,041

    I also have a Dewalt 708 & would not trade it for...

    I also have a Dewalt 708 & would not trade it for anything that I have seen. I'm amazed how long it stays accurate. I use a Forrest Chopmaster and get a great, accurate cut.
  22. Replies
    19
    Views
    1,149

    What kind of companies did you work for?

    What kind of companies did you work for?
  23. Replies
    46
    Views
    2,146

    I like the weight and precision of floor models. ...

    I like the weight and precision of floor models. I have a Jet with the three pulley design. I always change the pulleys to the required speed before drilling. I find that it takes almost no time...
  24. Picture of what was delivered. 423256

    Picture of what was delivered.

    423256
  25. Target Coatings Excellent Customer Service

    I received a shipment today from Target Coatings that was destroyed in transit. It was two quarts of product that both were opened. The shipper simply put what was left of the cans into a plastic...
Results 1 to 25 of 241
Page 1 of 10 1 2 3 4