Search:

Type: Posts; User: Timothy Robinson; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    2,576

    Sold one of the band-wheels and the lower trunion...

    Sold one of the band-wheels and the lower trunion assembly. Lower VS drive setup, transmission, tensioner, blade guide and counterweight, one of the bandwheels and the transmission...
  2. Replies
    25
    Views
    2,402

    I'm not too pleased with the castings on this...

    I'm not too pleased with the castings on this beast...There are voids and it appears that the ribs on the underside of the platten were molded by sticking some half-round sticks to the bottom of the...
  3. Replies
    14
    Views
    2,576

    Blade welder sold. To recap: the lower VS...

    Blade welder sold.

    To recap:
    the lower VS drive pulley setup, the linkage for the VS and 3-speed transmission are for sale as well as the tensioner, table, lower trunnion Blade guide and...
  4. Replies
    25
    Views
    2,402

    410922410921I managed to dent up the housing...

    410922410921I managed to dent up the housing removing the eccentric cam bearings so I'm looking into sources. Anyone have a good (read 'cheap') bearing source? the specs are "FAFNIR RA108" bearing...
  5. Replies
    14
    Views
    2,576

    I have been able to sell the upper variable speed...

    I have been able to sell the upper variable speed drive shaft/pulley unit. The lower unit (on the left with the spring) is still for sale. $150.
  6. Replies
    5
    Views
    1,811

    Don, did you have any luck finding a manual/parts...

    Don, did you have any luck finding a manual/parts list for your sander? I have the same machine and some of the specifics are different. For example, the spindles don't have external threads. The...
  7. Replies
    14
    Views
    2,576

    The upper and lower variable-speed shaft/pulley...

    The upper and lower variable-speed shaft/pulley units are out and for sale. Entire units are $150 each. You'll probably want to replace the pillows, as they're a little 'grindey' feeling but they...
  8. Replies
    14
    Views
    2,576

    In answer to someone's question, ("Is the blade...

    In answer to someone's question, ("Is the blade welder single phase?"). I think so. The motor plate says that it is single phase so that should go for the welder too since there doesn't appear to be...
  9. Replies
    14
    Views
    2,576

    This beastly table weighs almost 114 lbs. Gonna...

    This beastly table weighs almost 114 lbs. Gonna have to ship it freight if anyone wants it.
  10. Replies
    25
    Views
    2,402

    Doesn't look like a chip-breaker was OEM on this...

    Doesn't look like a chip-breaker was OEM on this particular machine. it has a scoop built into the hood. Don't know how effective it is at deflecting the debris but it doesn't seem like it would be...
  11. Replies
    25
    Views
    2,402

    Thanks Bill, that pdf is gold. Squares with what...

    Thanks Bill, that pdf is gold. Squares with what someone at OWWM.org told me. I'd never heard of such a thing.
  12. Replies
    14
    Views
    2,576

    Going ahead and putting up the...

    Going ahead and putting up the pictures...409924409926409927409928409929409930
  13. Replies
    25
    Views
    2,402

    Any ideas on fabricating a chip-breaker? It...

    Any ideas on fabricating a chip-breaker? It appears to be 10 or 8-gauge sheet which is bent on a brake and welded but I have no drawing to go by. Anyone have a belsaw who would be willing to give...
  14. Replies
    25
    Views
    2,402

    Update on the belsaw restoration...I'm getting it...

    Update on the belsaw restoration...I'm getting it apart and finding broken bits where it was mishandled. Cast iron is wonderful for its strength but it IS brittle. A few places on the flange/frame...
  15. Replies
    25
    Views
    2,402

    Joe, can you describe the pressure bar and chip...

    Joe, can you describe the pressure bar and chip breaker? I was looking at a massive Powermatic last week (24" I think) that had a bar with loose 1/4" wide weights which ride lightly on the...
  16. Replies
    14
    Views
    2,576

    OOPS. I was not looking at the saw table when I...

    OOPS. I was not looking at the saw table when I replied to Richard Newman's question. It does NOT have a miter slot. It has a slot through which the blade slides having also a steel plate insert. ...
  17. Replies
    14
    Views
    2,576

    It does. I have not got around to cleaning up...

    It does. I have not got around to cleaning up the table yet.
  18. Replies
    14
    Views
    2,576

    I was unable to get the link changed to something...

    I was unable to get the link changed to something that works so here is a new link to pictures of the bits and pieces of my salvage from the Powermatic 87 bandsaw. ...
  19. Replies
    25
    Views
    2,402

    Well, I found that single part number in picture...

    Well, I found that single part number in picture four in the parts list for my Belsaw model 912 so it appears that this is indeed a Belsaw.
  20. Replies
    25
    Views
    2,402

    How you going to get those elevation screws...

    How you going to get those elevation screws working again? Sprayed blaster PB on them and I intend to wire brush them but I think the scale is as deep as the threads. Pretty sure I am not going to...
  21. Replies
    25
    Views
    2,402

    Bill, I think it's 15" (I'm not near it now) and...

    Bill, I think it's 15" (I'm not near it now) and what does "more words tomake minimum" mean?
  22. Replies
    25
    Views
    2,402

    I actually own a belsaw planer/molder/sander...

    I actually own a belsaw planer/molder/sander which I have never turned on (It is stored in another county) I got this beast out of a junk pile compiled from county schools. The base might be...
  23. Replies
    0
    Views
    761

    Parts to build a bandsaw

    Hey Creekers

    If any builders are interested I am parting out a Powermatic 20-inch bandsaw. Might be some parts here you could use for your build. It's over in the classifieds. Here is the link...
  24. Replies
    14
    Views
    2,576

    Iíll work on it in a bit. Thanks for telling me....

    Iíll work on it in a bit. Thanks for telling me. Should be 11 pictures.
  25. Replies
    25
    Views
    2,402

    Help identifying a thickness planer

    Hey Creekers: I just acquired a massive-heavy thickness planer and cannot figure out what make it is. It was a school machine and the labeling is gone. Pictures follow...408577408578408580408581...
Results 1 to 25 of 32
Page 1 of 2 1 2