Search:

Type: Posts; User: Edward Dyas; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    392

    The best rip blade I've used is actually a fiber...

    The best rip blade I've used is actually a fiber cement blade where the 10" blade only had like 6 teeth.
  2. Replies
    5
    Views
    253

    Was it Purebond brand plywood? They are bad to...

    Was it Purebond brand plywood? They are bad to not fill knot holes in the core veneers where the outer veneer is laid over a hole. You can't see it until you put a finish on and the veneer wrinkles...
  3. Replies
    33
    Views
    1,153

    For me I think the most dangerous aspect of a...

    For me I think the most dangerous aspect of a jointer is the push blocks they give you when you buy a new jointer. I tried them for about an hour with the purchase of a new jointer and found they...
  4. Replies
    25
    Views
    773

    The "exterior" sheet good would just need to be...

    The "exterior" sheet good would just need to be plywood rated for exterior use, meaning it was laminated with veneers with a water resistant adhesive. If you cut apart an exterior slab door you will...
  5. Replies
    11
    Views
    410

    Does the machine have a light or something that...

    Does the machine have a light or something that would work on single phase? You may have three hot wires, one neutral and one ground. It would need the neutral if there is something single phase on...
  6. Replies
    18
    Views
    560

    I use different materials for different kinds of...

    I use different materials for different kinds of push blocks. It would be helpful to know what kind of push blocks you are using.
  7. Replies
    13
    Views
    522

    Bandsaw blades are like anything else, you can...

    Bandsaw blades are like anything else, you can get some good ones and some bad ones. The bandsaw blade material is made on a continuous roll and when made they pull out the length they need, cut it...
  8. Replies
    15
    Views
    559

    For that application I wouldn't recommend a PVA...

    For that application I wouldn't recommend a PVA glue. It tends to dry around the edges and stays wet in the middle for a long time. A UF glue would work alright.

    I don't see the point in trying...
  9. Replies
    8
    Views
    315

    If it were me I would cover it with formica. It...

    If it were me I would cover it with formica. It would be hard enough to last forever and would be completely waterproof. If you wish to paint it you might use an oil based enamel with a hardener....
  10. If the ridge is of sufficient size there...

    If the ridge is of sufficient size there shouldn't be any problem. A lot depends on whether the building is where there is heavy snowfalls. The ridge would be carrying the entire load of the roof.
  11. Replies
    13
    Views
    363

    Yea, use a nail set and sink the nails. Then many...

    Yea, use a nail set and sink the nails. Then many places you can get wood putty in different colors so when it's stained or finished the spots pretty much disappear. If you can only get putty in a...
  12. It's very rare for wooden table pins to swell. I...

    It's very rare for wooden table pins to swell. I think after working on probably a 1000 antique tables I've only had to sand the pins on one or two tables. Then it was only a 5 minute project. If I...
  13. Replies
    10
    Views
    682

    Is it really necessary to make the top 3" thick....

    Is it really necessary to make the top 3" thick. For most applications a single 3/4" sheet of plywood has met my needs.
  14. Replies
    14
    Views
    468

    A cup warp is normally caused by a imbalance in...

    A cup warp is normally caused by a imbalance in moisture content from one side to the other. Assuming you finished the front and not the back there is likely a crown on the back side. If that is the...
  15. The type pins isn't as critical as getting the...

    The type pins isn't as critical as getting the holes accurate. You might lay both sides of your top on a table with the leaves in it and draw a line across all the pieces. Then use an actual...
  16. Replies
    7
    Views
    534

    If it were me I would use titebond III or...

    If it were me I would use titebond III or equivalent. I've had joints come apart with polyurethane adhesives before.
  17. Replies
    18
    Views
    1,015

    Generally kitchen and bath cabinets are a...

    Generally kitchen and bath cabinets are a different class of woodworking than furniture. I don't mind using slides in cabinets but use conventional drawers in furniture.
  18. Replies
    34
    Views
    1,274

    You would have more issues with rust keeping the...

    You would have more issues with rust keeping the saw outdoors but if you coat the raw metal parts with WD-40 and cover it with a tarp when not in use you shouldn't have a problem. My shop is under...
  19. Replies
    26
    Views
    1,062

    I've been using the harbor freight helmet for...

    I've been using the harbor freight helmet for several years and I don't have any complaints.
  20. Replies
    14
    Views
    584

    Plexiglass will cut fine on the bandsaw. If you...

    Plexiglass will cut fine on the bandsaw. If you have a fine tooth blade it will make better looking edges.
  21. Replies
    2
    Views
    178

    The width of the table is just determined by the...

    The width of the table is just determined by the travel. I would use something very hard underneath where the saw cuts. They tend to wallow out a wide groove which in turn causes chip outs on the...
  22. Replies
    7
    Views
    342

    As long as you don't wrap the table with plastic...

    As long as you don't wrap the table with plastic it shouldn't hurt anything to ship it. I wouldn't use any packing peanuts either since the solvents could melt them. Now if the box gets to smelling...
  23. Replies
    8
    Views
    408

    When I build cabinets for a customer the old...

    When I build cabinets for a customer the old cabinets I take out usually ends up being used in my shop.
  24. Replies
    19
    Views
    921

    I would trust anything made by Northfield....

    I would trust anything made by Northfield. Chances are with the exception of maybe wiring or safety equipment the saws are made identical to saws made 50 years ago. They are still in business and...
  25. Replies
    13
    Views
    614

    A lot of what you pay for prescriptions goes to...

    A lot of what you pay for prescriptions goes to lawyers and people trying to get rich quick off the system.
Results 1 to 25 of 249
Page 1 of 10 1 2 3 4