Search:

Type: Posts; User: Bob Vavricka; Keyword(s):

Page 1 of 17 1 2 3 4

Search: Search took 0.23 seconds.

  1. Replies
    17
    Views
    1,103

    My wife has one she purchased. It looks to me to...

    My wife has one she purchased. It looks to me to be made out of ash.
  2. Replies
    3
    Views
    1,123

    Shameless bump. Price reduced to $75 each. I...

    Shameless bump. Price reduced to $75 each. I would really like to get these out of my way. Cross listed
  3. Replies
    3
    Views
    1,123

    Sewing Machine Air Lift (2)

    I bought 2 Horn of America Sewing Machine lifts to make cabinets for my wife several years ago. We ended up going another way with the cabinets and I would like to get these out of my way. Sticker on...
  4. I did a "planked" ceiling in our bedroom. I used...

    I did a "planked" ceiling in our bedroom. I used an engineered flooring that was pretty thin, I think 5/16" because our ceilings are already low in the upstairs. The ceiling had popcorn texture that...
  5. Replies
    7
    Views
    495

    GFIC outlet with usb charging port

    Do they make a GFIC outlet that has a built in usb charging port? I've searched for one with no luck.
  6. Replies
    7
    Views
    554

    We got the debit cards and I nearly threw them...

    We got the debit cards and I nearly threw them away without opening the envelope. I also transferred the money from the card to my checking account, but there was a limit on how much you could...
  7. Replies
    6
    Views
    842

    Bruce, I've Goggled the motor model which is I/R...

    Bruce, I've Goggled the motor model which is I/R # 56283138 numerous times and ways and most often I get a 5HP motor with a different frame type and higher FLA amps. I do have a new set of contacts...
  8. Replies
    6
    Views
    842

    David, thanks for a detailed reply. I wasn't...

    David, thanks for a detailed reply. I wasn't using the right term to search. The link you posted had what I needed, but unfortunately, they required a $500 order to use a credit card so with that...
  9. Replies
    6
    Views
    842

    Compressor motor

    My compressor quit (Ingersoll Rand) and I determined the start capacitor was bad, it had went bad a few years ago also, so I got a new capacitor and put it on. When I turned it on, the motor vibrated...
  10. OK, I didn't understand from your original post,...

    OK, I didn't understand from your original post, that the duct work was going to be replaced.
  11. If the old ductwork is gone, why not patch the...

    If the old ductwork is gone, why not patch the hole and get rid of the grille? If you want the grille, cut some narrow strips of wood (I use plywood so it doesn't split-1/2" baltic birch works good)...
  12. Replies
    16
    Views
    883

    433489This is what I think of when I hear weed...

    433489This is what I think of when I hear weed whip. It's like the one I grew up with. Also called and idot stick.
  13. Tony, thanks for the reply. I checked them out,...

    Tony, thanks for the reply. I checked them out, but it was cheaper to buy directly from Epilog which was suprising and the tech I have talked to at Epilog has been especially helpful.
  14. Replacement Epilog laser mirrors and lens

    Are there 3rd party suppliers for mirrors and lens for an Epilog mini 18 laser?
    If so, have you used any you would recommend?
    Thanks.
  15. Replies
    19
    Views
    3,484

    I put OSB in my shop and primed the sheets with...

    I put OSB in my shop and primed the sheets with oil based Kilz before putting it up and then top coated it with a latex paint after it was up and it looks good. I did need one small piece to finish...
  16. Replies
    10
    Views
    1,555

    You might look for Baalmic Glaze it is thicker...

    You might look for Baalmic Glaze it is thicker and sweet, I look for one with no added sugar since I'm limiting sugar. There is some natual occuring sugars in it. I use it as a no salt added, no fat...
  17. Replies
    8
    Views
    1,076

    Only on the hot water side, not on cold water.

    Only on the hot water side, not on cold water.
  18. Replies
    8
    Views
    1,076

    No, He is on City water.

    No, He is on City water.
  19. Replies
    8
    Views
    1,076

    Hot Water sputters

    My son had a new hot water heater put in over a month ago and when I was visiting he showed me that when you turn on the hot water on faucets connected to that hot water heater it sputters like when...
  20. Replies
    3
    Views
    689

    Most vacuum chambers I have seen/used have at...

    Most vacuum chambers I have seen/used have at least a clear top so you can control the amount of "foam" created when you first draw the vacuum and a lot of air is being pulled out of the wood. This...
  21. Replies
    3
    Views
    689

    You might check out Turntex.com, Curtis Seebeck...

    You might check out Turntex.com, Curtis Seebeck is well known in the woodturning community in my area for his chambers and "cactus juice" stabalizing resin. Charles Wagoner is a member of my...
  22. Replies
    8
    Views
    1,259

    Cutting the cardboard and cloth for the bottom...

    Cutting the cardboard and cloth for the bottom like Mike and Al do might be better than wrapping it--Less thickness. For the sides I think I would still wrap it on the top edge. I think it gives a...
  23. Replies
    8
    Views
    1,259

    It's been awhile since I did something similar,...

    It's been awhile since I did something similar, but I cut thin cardboard/heavy cardstock pieces to fit the bottom and cover it with the cloth, wrapping the cloth around the cardboard and cutting the...
  24. Is it safe to laser cut tool drawer foam

    I bought some tool drawer foam where you cut out areas of one layer for your tools and then adhere it to a backing layer. All I could find on the type of material was that it is cross-link,...
  25. Replies
    39
    Views
    3,577

    I would go to a local machine shop if you have...

    I would go to a local machine shop if you have one in the area.
Results 1 to 25 of 418
Page 1 of 17 1 2 3 4