Search:

Type: Posts; User: Mark Daily; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,134

    Matt, that’s a beautiful table. How did you put...

    Matt, that’s a beautiful table. How did you put the “C” in the middle?
  2. Replies
    7
    Views
    491

    The filters of the RZ mask look like thin pieces...

    The filters of the RZ mask look like thin pieces of fabric. I doubt they could filter out small particles as well as cartridge filters like those on the 3M 7500 series half-mask filters which is what...
  3. Replies
    8
    Views
    654

    I’ve sprayed a lot of Deft lacquer and won’t use...

    I’ve sprayed a lot of Deft lacquer and won’t use anything else in rattle cans. I spray one thin coat, wait 30 minutes and spray another. Let that dry 30-60 minutes and sand lightly using 1500 grit...
  4. Replies
    12
    Views
    571

    Dan, it looks fabulous! Very clean & precise...

    Dan, it looks fabulous! Very clean & precise looking. How long did it take?
  5. Replies
    27
    Views
    1,078

    Rats...:mad:

    Rats...:mad:
  6. Replies
    15
    Views
    690

    Jet Tools bought Performax several years ago. Try...

    Jet Tools bought Performax several years ago. Try contacting them using the below link:
    https://www.jettools.com/us/en/service-and-support/customer-support/
  7. Replies
    27
    Views
    1,078

    I’ve seen Mike Holmes use Quietrock in a couple...

    I’ve seen Mike Holmes use Quietrock in a couple episodes and he said it worked very well.
    Dont know anything about the cost or availability in your area but here’s a link:
    ...
  8. I too have a mini-split and it works much better...

    I too have a mini-split and it works much better than a portable. If you can afford one, you won’t be disappointed.
  9. Replies
    10
    Views
    1,202

    I too would get the jointer/planer first. I have...

    I too would get the jointer/planer first. I have a Grizzly 14” G0555 bandsaw I got 15 years ago and it does everything I need it to. I have a 6” riser block for it but have never used it as I never...
  10. Replies
    11
    Views
    466

    How do you guys feel about Thompson’s Water Seal?

    How do you guys feel about Thompson’s Water Seal?
  11. Thread: Glue Guns?

    by Mark Daily
    Replies
    12
    Views
    603

    I bought the Hipurformer system when it first...

    I bought the Hipurformer system when it first came out. Rarely used it because they had a problem with the glue cartridges not opening up to use more than once. They fixed that but the cartridges now...
  12. Replies
    7
    Views
    669

    There sure are Dennis- they’re just so darn hard...

    There sure are Dennis- they’re just so darn hard to find!
  13. Replies
    17
    Views
    957

    [QUOTE=Bill Dufour;2935714] Bill, Iíve done roof...

    Bill, Iíve done roof inspections with my drone. Landing on a sloped roof is not an option but the camera is stabilized to get good video or still pics. Areas that might need attention will require an...
  14. Replies
    17
    Views
    957

    Edward, you might try sending that photo to pest...

    Edward, you might try sending that photo to pest control companies, as they are scarce in your area. Or maybe a university extension department to at least identify the bug.
    Once you know what it...
  15. Replies
    4
    Views
    327

    Lee Valley, Van Dyke Restorers, and Google. Iíve...

    Lee Valley, Van Dyke Restorers, and Google. Iíve found lots of neat hardware at places I had never heard of until I did a Google search.
    Like www.coolknobsandpulls.com
  16. I use Xfasten carpet tape. 2” x 20 yards, $11.97...

    I use Xfasten carpet tape. 2” x 20 yards, $11.97 at Amazon. It’s thin, comes off clean and very strong so you need to use very little. A roll usually lasts me a year or more.
  17. Replies
    23
    Views
    1,675

    That is FAB-U-LOUS! Great job!

    That is FAB-U-LOUS! Great job!
  18. Replies
    3
    Views
    470

    Great craftsmanship and damn funny!

    Great craftsmanship and damn funny!
  19. Replies
    52
    Views
    3,581

    Alan, if you check post #24 by David Morse he has...

    Alan, if you check post #24 by David Morse he has links to what I think you’re looking for.
  20. Replies
    47
    Views
    2,907

    Jim, I think what you and everyone else are...

    Jim, I think what you and everyone else are seeing, is caused by a couple of generations of people who donít know what good quality is and donít appreciate good craftsmanship. All they care about is...
  21. FWIW I haven’t had any issues uploading photos. I...

    FWIW I haven’t had any issues uploading photos. I discovered that depending on the original photo orientation (landscape vs portrait) I need to open the photos in a photo editor then re-save them. It...
  22. Replies
    52
    Views
    3,581

    David, my Dylos manual states ďsmall particle...

    David, my Dylos manual states ďsmall particle concentration is always displayed to the left and large particle concentration to the right.Ē No mention that the left is the total large & small.
  23. Mark, thanks for mentioning Ramboard. I’ve never...

    Mark, thanks for mentioning Ramboard. I’ve never heard of it before, but I can think of a number of past projects I could’ve used it for. I’ll just file this away in the ole’ brain-box for future...
  24. Replies
    7
    Views
    463

    I painted my garage doors. Oh wait, that’s not...

    I painted my garage doors. Oh wait, that’s not woodworking... Never mind..:confused:
  25. Replies
    7
    Views
    463

    Lisa, I recently made a large cutting board and...

    Lisa, I recently made a large cutting board and used “Tried & True” danish oil. It is a polymerized linseed oil which dries in about 8 hours and is food safe.

    I found it on Amazon for about...
Results 1 to 25 of 88
Page 1 of 4 1 2 3 4