Search:

Type: Posts; User: Kory Watson; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. I may indeed do this regardless, as we have 3...

    I may indeed do this regardless, as we have 3 roof vents that could ventilate a "mini" attic space.
  2. > I'm concerned with your roof structure. Looks...

    > I'm concerned with your roof structure. Looks like 1 out of 3 rafters is supported by trusses. Take a look at it from the outside on a ladder. Does it sag any between trusses?

    No sag at all! The...
  3. I'm curious why you wouldn't do foam sealing. Is...

    I'm curious why you wouldn't do foam sealing. Is there not a risk of condensation without a solid air seal?
  4. We just replaced the roof. Adding insulation on...

    We just replaced the roof. Adding insulation on top of the sheathing would have been too expensive as we would have needed to re-do all of the fascia.
  5. Did some research on this. How do you seal the...

    Did some research on this. How do you seal the underside of the roof? Do you pay a closed cell contractor to spray an inch of foam then fill the rest with rock wool?
  6. Definitely no way I'd bother with DIY foam. It's...

    Definitely no way I'd bother with DIY foam. It's nasty stuff.
  7. Do you have ventalation concerns? If I installed...

    Do you have ventalation concerns? If I installed rock wool, it would need to be touching the roof sheathing directly. My understanding is that will do major damage over time.
  8. We need to do the insulation inspection, and will...

    We need to do the insulation inspection, and will close up the walls afterwards with ply. Inspector has OK’d this plan. Drywall for fire recommended but not required as it is a detached garage.
    ...
  9. How to go about insulating 2x4 vaulted ceiling in detached garage?

    I've been renovating a 1940s detached garage.

    The walls were reframed & insulated, and new electrical run. The last step before drywall / ply is insulating the ceiling.

    My problems here are:
    *...
  10. Thread: 220v Plugs

    by Kory Watson
    Replies
    70
    Views
    13,885

    Could you clarify what you mean by 3-wire or...

    Could you clarify what you mean by 3-wire or 4-wire? On a 240V GFCI, with what I would consider the most common amperage for a shop (20), you only need standard 12/2 cable. A neutral does not need to...
  11. Replies
    7
    Views
    1,025

    The blade is plumb, just not the guides...

    The blade is plumb, just not the guides...
  12. Replies
    7
    Views
    1,025

    This is a laguna 14BX. I couldn't figure out how...

    This is a laguna 14BX. I couldn't figure out how to adjust this part of the guide but I'm open to suggestions. I'm sure there's some way to do it...
  13. Replies
    7
    Views
    1,025

    Bandsaw Blade Guide Help

    Picked up my new bandsaw and noticed that the blade guide isn't square with the table. Is this pretty typical or is something off on my new machine?

    Thanks.

    491616
  14. It’s here…

    Too bad I haven’t wired in a 240V outlet yet. And gotta wait until Tuesday for the mobile base.

    https://imgur.com/a/91LPP7s
  15. Thanks so much for the link! I was looking all...

    Thanks so much for the link! I was looking all over for this and couldn't find it...
  16. Update: I went with the 14BX deal. Now I need...

    Update: I went with the 14BX deal.

    Now I need to put in a 220V outlet…

    Would have loved a 17” bandsaw, but upon seeing them in person at the store, they were way too big for my space.
  17. Unfortunately, the MM16 guy isn't responding. Was...

    Unfortunately, the MM16 guy isn't responding. Was holding out in hope for a couple of days, but I guess it probably sold at some point but he didn't take the post down :(

    Speaking of that... I...
  18. I'm not sure. Grizzly probably sold it in the...

    I'm not sure. Grizzly probably sold it in the early 2000s alike many other brands (eg. JET, STAR, KING etc.). It's a CT-200.
  19. I'm not sure, but I can check. The head is quite...

    I'm not sure, but I can check. The head is quite rusted, so I'm going to spend $400 for a SHELIX helical to replace it regardless. This is a CT-200, which was sold by many many brands (the 8'' JET...
  20. It's actually visually identical to the STAR...

    It's actually visually identical to the STAR machine. They probably both came from Geetech.
  21. Quick update. Managed to snag the "$800" Geetech...

    Quick update. Managed to snag the "$800" Geetech jointer for $200. So went with that. Needs a little bit of T.L.C (rust removal & helical blade) but it seems like a crazy good deal overall,...
  22. Unfortunately it's only a 6'' jointer. I'm...

    Unfortunately it's only a 6'' jointer. I'm shooting for 8''.
  23. Is this a good deal for a jointer? Help me pick a used 8''.

    https://kpr.craigslist.org/tls/7560542900.html This guy is selling a David & Wells 8'' jointer for $750. I've been in the market for an 8'' jointer and this is finally one within my price range....
  24. I found a MM16 2003 model (3.6hp) for $1400 a few...

    I found a MM16 2003 model (3.6hp) for $1400 a few hours away. Maybe that's a good choice? A little worried about the mobility bit looks nice otherwise.
  25. Thanks all for the advice. Folks seem to be...

    Thanks all for the advice. Folks seem to be pushing for the 17'' 240V. I was indeed planning to head to Bellingham to pick a Grizzly up, since they're all available there :)

    My second Q, is if I...
Results 1 to 25 of 26
Page 1 of 2 1 2