Search:

Type: Posts; User: Bill Dufour; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    13
    Views
    462

    This should help since the 12/14 is just a...

    This should help since the 12/14 is just a overgrown unisaw.
    Bil lD.
    http://wiki.vintagemachinery.org/1214ArborBearings.ashx
  2. Hollow core door of the correct width.

    Hollow core door of the correct width.
  3. Replies
    9
    Views
    413

    Donner pass rotary plow in action....

    Donner pass rotary plow in action.
    https://www.youtube.com/watch?v=RjBQ3MaBYiU

    And some jet blowers...
  4. Replies
    13
    Views
    502

    German beer died green, German sausage died...

    German beer died green, German sausage died green, green lederhosen for the shop.
    Bill D.
  5. Replies
    13
    Views
    502

    Paint some vacuum hose Festol green and use it as...

    Paint some vacuum hose Festol green and use it as a garland. Or a sash for his wife/girlfriend. Or his wife(not You!) could make a green sash that says Festool Queen or Miss Festool, and wear only...
  6. Replies
    41
    Views
    664

    Electric oven is prefered by many cooks. Also...

    Electric oven is prefered by many cooks. Also gas ovens are no longer vented to a chimney(after 1950's) so all that heat, CO, and fumes go into the house.
    OP: is this a convection oven, if so turn...
  7. That sounds like a good solution. I suppose I...

    That sounds like a good solution. I suppose I could mount a motor in a plinth and set the planer up on that. Of course that would raise it almost a foot.
    Bill D
  8. Replies
    6
    Views
    258

    JB weld worked on the aluminum guide finger of my...

    JB weld worked on the aluminum guide finger of my jig.
    Bill D
  9. Replies
    2
    Views
    371

    Practical Machinist

    Practical Machinist
  10. Replies
    8
    Views
    363

    You could build the taper out of bondo or tile...

    You could build the taper out of bondo or tile grout keeping it the 1/8 below the wood so the top surfaces match.
  11. Replies
    2
    Views
    230

    How wide a cut? Can the fancy cutterhead be moved...

    How wide a cut? Can the fancy cutterhead be moved to a different machine? The cutterhead alone may be worth the price especially if it can be swapped into a heavy duty machine.
    Bill D.
  12. 200-300 sounds about right. Does it have a table...

    200-300 sounds about right. Does it have a table raising system? Quill stroke the longer the better. My walker turner 20" DP is 6" quill stroke so it saves moving the table up and down a lot. i...
  13. rockwell or powermatic 18" planer, motor relocation

    I am considering buying an older 18" planer. These are belt drive with the motor completely outside the base on a shelf half way down or so. Any one done a relocation to put the motor inside the...
  14. Size, Hp, floor or benchtop, MT # Bill D

    Size, Hp, floor or benchtop, MT #
    Bill D
  15. Replies
    13
    Views
    356

    Putting tongue and grove on 7.5" fence board 5...

    Putting tongue and grove on 7.5" fence board 5 feet long about fifty feet of fence filled up 30 gallon drum.
    Bill D.
  16. Replies
    5
    Views
    178

    Blades are worn in the middle so they cut shallow...

    Blades are worn in the middle so they cut shallow resulting in the convex cut down the length of the board. Time to get the knives sharpened.
    Bill D.
  17. Replies
    13
    Views
    462

    Note that pretty much all ball bearings are...

    Note that pretty much all ball bearings are metric so measure them in metric. Do not try to measure in English units and convert. Some limited farm equipment may have semi custom inch bore bearings...
  18. Remove the setscrew and look inside to see if...

    Remove the setscrew and look inside to see if there is another one under the one you removed. HF, I doubt they went to the trouble and expense. Pry only on the boss not the fan blades. Can you...
  19. I would be shocked if the plan company did not...

    I would be shocked if the plan company did not estimate the concrete required for several different type and thickness of foundation. You may to ask for them to email it to you.
    Bil lD.
  20. Replies
    20
    Views
    414

    If you increase pump rpm you have to lower cutout...

    If you increase pump rpm you have to lower cutout pressure. Most are set at 150 PSi or higher. For most folks 100-120 PSi is more then enough.
    The real way to figure out cutout pressure is to run...
  21. The company should supply foundation plans with...

    The company should supply foundation plans with bolt locations. They may have several styles with single slab or a thicker perimeter foundation.
    Bill D
  22. Replies
    23
    Views
    1,080

    Morris chair that reclines? Find the cushions...

    Morris chair that reclines? Find the cushions first and modify the design so they fit.
    Bill D.
  23. Replies
    13
    Views
    462

    Release the belt and turn on the motor and see if...

    Release the belt and turn on the motor and see if the rumbling is still there. If not it is the arbor. I would replace all four bearings as long as you have the top off. I would say the grease has...
  24. Replies
    57
    Views
    2,445

    I like to use aluminum foil for paint masking. ...

    I like to use aluminum foil for paint masking. Holds nicely to curves and self holds when crumpled around a feature.
    Bil lD
  25. Replies
    25
    Views
    934

    I think he means delta/rockwell 14" BS

    I think he means delta/rockwell 14" BS
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4