Search:

Type: Posts; User: David Utterback; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    255

    Very nice and elegant. I agree with the comment...

    Very nice and elegant. I agree with the comment above that the legs could be tapered more. Thanks for sharing
  2. Have they been painted on both sides in which...

    Have they been painted on both sides in which case the work is even more than we see? Congratulations to you and your sister and thanks for sharing.
  3. Replies
    11
    Views
    412

    We have it installed in our kitchen. It is very...

    We have it installed in our kitchen. It is very attractive , IMHO, although the installers left a few minor problems. A wide variety of finishes are available but I do not know the details. Our Bruce...
  4. Replies
    14
    Views
    400

    I have learned that splats are panel backs in...

    I have learned that splats are panel backs in chairs. I am able to find examples when I search websites using the term. They are generally attached to the crest rail and a lower rail or seat with...
  5. Replies
    17
    Views
    608

    My wife, 2 sisters and I toured the Gamble House...

    My wife, 2 sisters and I toured the Gamble House in early March. It was wonderful with many surprises, especially in the details. A couple of rooms had Stickley furniture. The docent was very well...
  6. Replies
    2
    Views
    163

    Simple is elegant. I really liked working with...

    Simple is elegant. I really liked working with ash. Thanks for sharing.
  7. Replies
    14
    Views
    400

    The convection setting did get the water a little...

    The convection setting did get the water a little warmer but also roasted the wood. It split along the grain when I clamped it in the form. The wood did not seem at all moist when I took it from the...
  8. Replies
    14
    Views
    400

    This experiment has failed and I am at a complete...

    This experiment has failed and I am at a complete loss to understand why:confused:. I preheated the oven and poured boiling water into a cake pan and then placed the board on the rack above. Since...
  9. Replies
    19
    Views
    626

    I have one of those, Bill, that I bought from Lee...

    I have one of those, Bill, that I bought from Lee Valley a couple of years ago for about $50 IIRC. I have to disconnect the battery section after each use or they will fully discharge. Hope yours...
  10. I made a stand from 2x6 construction lumber that...

    I made a stand from 2x6 construction lumber that had a lower "shelf" high enough to clear my hydraulic car sack. HF has them for $80 (minus 20% with coupon). Once in the basement, I can easily move...
  11. Replies
    8
    Views
    635

    The web site example does is not designated as...

    The web site example does is not designated as the SE. Looks like they are different models and maybe materials.
  12. Replies
    14
    Views
    400

    Oven for steaming?

    I would like to bend a 3/8" thick air-dried cherry board across its width to use as a chair back splat. The bend would only be about 1/2" over a 9" width. Could I steam the board in the kitchen oven...
  13. Replies
    22
    Views
    706

    Can you glue an inch or two the snug end and let...

    Can you glue an inch or two the snug end and let the remainder of the joint move?
  14. Replies
    8
    Views
    607

    Cool chair and amazingly clean shop.

    Cool chair and amazingly clean shop.
  15. Replies
    9
    Views
    371

    The finish really makes them even more handsome....

    The finish really makes them even more handsome. Well done!
  16. Nice lines and concept. Bet it looks even better...

    Nice lines and concept. Bet it looks even better when finished.
  17. Replies
    30
    Views
    1,147

    I also suggest being a bit patient and finding a...

    I also suggest being a bit patient and finding a good used saw. I just sold my PM 66 which was replaced with a Sawstop PCS. There seems to be a ready supply of used 66's and uni's in Cincinnati at...
  18. I am assembling my new-to-me Sawstop PCS that...

    I am assembling my new-to-me Sawstop PCS that came with the overarm dust collector. Have not tried it out yet but, as Edwin says, the dust collection is supposed to be very good.

    A general rule...
  19. Replies
    13
    Views
    617

    Just sold mine with the same motor and...

    Just sold mine with the same motor and manufacturing date as yours. I considered it a lifetime saw but got a great deal on a nearly new SawStop (which is still being assembled). My 66 deal included a...
  20. Amazing! Too nice to let the toddlers get their...

    Amazing! Too nice to let the toddlers get their hands on it. Do you have a display of your pieces? Would be nice to see your collection.
  21. Replies
    27
    Views
    1,805

    Are the results good when using rough cut, air...

    Are the results good when using rough cut, air dried lumber that may not be completely flat? I am not talking about a big bow or twist in the board but maybe some slight cupping. Thanks
  22. Replies
    15
    Views
    517

    Do the mesh abrasives work with ETS125?

    Do the mesh abrasives work with ETS125?
  23. Replies
    15
    Views
    583

    Kitchen Aid has a mixer attachment that cuts...

    Kitchen Aid has a mixer attachment that cuts multiple widths of pasta. At $170, it is a bit steep. May need to share with the cook to justify the cost.
  24. dell-inspiron-15-6-touch-screen-laptop-intel-core-...

    dell-inspiron-15-6-touch-screen-laptop-intel-core-i5-8gb-memory-256gb-solid-state-drive-black/6373812 for $349.

    I just saw this laptop deal that I thought was good. Had I seen it before I recently...
  25. Replies
    8
    Views
    441

    Very nice contrasting colors and grain. Thanks...

    Very nice contrasting colors and grain. Thanks for sharing.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4