Search:

If you completed a torsion box with MatchFit dovetail clamps, please share with the group.

Nice innovation on the lever clamp to hold down both the stock and backer board. :) With my prototype coping sled, I have experienced movement of backer board because I had a single foot on the lever...

I Googled "0.5 mm white lead" and got the following link: https://www.aliexpress.com/item/0-5mm-white-pencil-leads-2-cases-36-40-pieces-leads-refill-special-white-mechanical-pencil/32841792763.html...

Perhaps my information was not available in 2005 when this thread was started.403188

Here is the link to the SawStop Overarm Dust Collection that I am considering; https://www.sawstop.com/table-saws/by-model/overarm-dust-collection.

I have owned the SawStop Professional Cabinet Saw for several years and am contemplating adding above table dust collection. The two options I am considering are 1) Shark Guard and 2) SawStop Over...

Thanks for all your suggestions. The box is complete. While very functional, it is not particularly pretty. There were a couple of screw ups that I will pass on. The left to right width of one of the...

Thanks Charlie Hinton for your suggestion. I have implemented it as shown in the attachments. I don't think I made my original post clear. My issue is that when you have a repeated rabbet or groove...

I am building a box to store my DowelMax dowel jig and accessories. I modified a design I found from a youtube video and want to build it from 1/2" Baltic Birch plywood with 1/4" Melamine for some of...

William: I am not sure I followed your suggestions on increasing strength of cabinet. Is this what you had in mind? I obviously left out some joinery details. Clarification would be appreciated....

Julie: You have about 9 months of use of the mobile stand so how about an update. The lessons learned are always of value to those of us that are considering going down the same path. I have never...

I just finished building the Wood Smith plans (2012, SN10936) for the roll around cart for a Fein Turbo II shop vac/Dust Deputy combination and I too struggled with the hoses. After a lot of...

Victor: Did you follow through on the purchase of the MLCS stackable set. I am considering purchasing it.

I am considering purchasing the Infinity Precision Twist Adjustable slot cutter (model number 61-613). See web site...

I purchased the Porter Cable 557 Plate Joiner (biscuit joiner) in June 2017 and played with it on a miter joint in which the point of the miter was the reference point (or line); see Figure 36, page...

I bought the Makita SP6000J1 and was surprised that the saw base was some kind of hard plastic instead of metal. Before actually using the saw, I wanted to see if there had been any issues with the...

I hope Alan Schaffter is still following this thread because I want to give him a big "shout out" for this great post. No more than 15 minutes prior to finding this post, I had opened up my DJ20 and...

I have taken ideas from the forum and implemented them on my 14" Delta band saw. What I implemented did not alter the bandsaw with the exception of two drilled and tapped holes. I documented the...

I appreciate your article and the time spent responding to questions. My shop was formerly an artist studio but the lighting is inadequate for woodworking purposes. The dimensions are roughly...

John: What was the source for the 4" fitting you attached to the lower bandsaw door?

Scott:
I am trying to reverse engineer your hardware in the closeup picture of the vertical wall mounted duct run.
1. Is your strut 1 5/8"x13/16" 14 gage?
2. Is the threaded rod 1/4" or 3/8"...

Scott: This information has been very helpful. Thanks, Ben

Mike: The pictures are great. In my case, most of the ducting will be mounted to the wall because my ceilings are 13 ft high. I want to have my ducting about 7 ft off the floor. My ducting is...

I am inexperienced at posting on this site and I see that I should have been much more specific. Here are some specific questions:

For those that used Nordfab, would you share some pictures?
...

I am in the process of designing my first dust collection system and I want to use metal piping available from Nordfab. These products can be purchased from WW Grainger, Grizzly and possibly other...