Search:

Type: Posts; User: Nick Michalares; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.21 seconds.

  1. Replies
    6
    Views
    342

    Maybe you need to look into burnishers. Carbide...

    Maybe you need to look into burnishers. Carbide works for brass, diamond will work for brass, alum & glass. You will need the slide working, the "knurled barrel" above the spring increases/decreases...
  2. took 15-1/2 years, but my LS900's tube finally...

    took 15-1/2 years, but my LS900's tube finally called it quits That's gotta be a record. I have not heard of a laser tube lasting that long!
  3. Replies
    7
    Views
    680

    A guy I know in Michigan sent his to Photo Vac,...

    A guy I know in Michigan sent his to Photo Vac, they said it was a circuit board problem and charged him $50 bucks to repair it. Might try them.
  4. Replies
    4
    Views
    442

    OOhhh, good idea! Thanks.

    OOhhh, good idea! Thanks.
  5. Replies
    2
    Views
    334

    Check your connections.

    Check your connections.
  6. Replies
    7
    Views
    680

    Isn't Evergreen the one I've heard some bad...

    Isn't Evergreen the one I've heard some bad things about? They're the cheapest, but... I know Photo Vac in Ohio is pretty reliable. They do mostly medical lasers. https://photovaclaser.com/
  7. I've found the manual for this. Email me if you...

    I've found the manual for this. Email me if you want it. Too big to attach here.
  8. This model was declared obsolete in 2017, as was...

    This model was declared obsolete in 2017, as was the Lasertop V1. It runs with a proprietary program, originally I'm pretty sure. I haven't had experience running it from anything else and I don't...
  9. I think this program is for their dot impact...

    I think this program is for their dot impact printers, they're Technifor, too.
  10. Replies
    7
    Views
    2,714

    Laser Alignment

    Without a manual or expert guidance, I don't want to start cranking on screws and through everything off that may not need alignment.

    Your best bet would be to call Gravotech and schedule a Tune...
  11. Replies
    6
    Views
    1,120

    Looks like a fun place to be

    Looks like a fun place to be
  12. Replies
    6
    Views
    1,120

    Installing that belt Always reminded me a little...

    Installing that belt Always reminded me a little of what Rube Goldberg's mind must be like: ...
  13. Replies
    8
    Views
    3,119

    Here's what the code means: 04 LASER FAULT ...

    Here's what the code means: 04 LASER FAULT Fault_laser Laser General laser fault. "H" stands for Hardware, so it could have been worse. There's a pretty good tree of suspects for this, few of...
  14. Replies
    9
    Views
    1,467

    800.843.7637 X 4. May have to leave a number for...

    800.843.7637 X 4. May have to leave a number for call back or email askservice@gravotech.com
  15. Whatever happened with your M40?

    Whatever happened with your M40?
  16. Gravotech support

    Mike,
    There are quite a few different machines available and like anything else, every tech may not have all the answers for all situations on the spot. It is my understanding that the situation...
  17. MD40 engraver

    Send me some pix of what you have with a phone number and I can probably help you. You do need the USB dongle to run the software which you hopefully have. Gravotech will most certainly help you...
  18. Replies
    5
    Views
    1,462

    Wiring issue

    Probably a wiring issue. Do a continuity test on the wires going to the motor. Sometimes you can wiggle the wires and make it come and go which will narrow it down.
  19. Replies
    45
    Views
    10,758

    Here are some other models to check out:...

    Here are some other models to check out:
    http://www.gravograph.co.uk/engraving-machines/laser-applications-selection-guide.php
  20. Replies
    3
    Views
    1,179

    Vision Series one controller

    Vision no longer has main boards for those controllers and cannot get any made. You don't see lots of used Vision equipment available, that table is most likely a real brute, they last pretty good. ...
  21. If it is Cipher software, that manual is...

    If it is Cipher software, that manual is available on this link: http://www.visionengravers.com/support/vision-engraver-manuals.html#Engraving-Routing-Software-Manuals
    You want the Vision Windows...
  22. Replies
    7
    Views
    1,651

    Bruce, I do some work with the used equipment. ...

    Bruce, I do some work with the used equipment. Is it a Superpro style controller, or the real old DOS upgraded to run off an old DOS 486 type computer? I have a couple around me for sale, one in...
  23. Rubber Stamp & Engraving Co. (Pty)Ltd, 3 Appel...

    Rubber Stamp & Engraving Co. (Pty)Ltd, 3 Appel Rd, Kramerville, Sandton, SOUTH AFRICA. Trotec has a distributor in South Africa, try

    Tel:
    +27 21 448 7008


    Fax:
    +27 21 448 7014
  24. Replies
    6
    Views
    2,044

    The 0 at the end is not entered, it just...

    The 0 at the end is not entered, it just indicates your software is registered correctly. If it does not show up, your license files may not be in there. There are 2 license files that may have to...
  25. Replies
    4
    Views
    1,117

    In a pinch, I have gotten a bottle of Everclear,...

    In a pinch, I have gotten a bottle of Everclear, pure grain alcohol at the liquor store and would moisten a high quality Q tip with it and clean the lens/mirrors with a rolling motion rather than...
Results 1 to 25 of 64
Page 1 of 3 1 2 3