Search:

Type: Posts; User: Johnny Barr; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Brilliantly, Michael. After 12 months the surface...

    Brilliantly, Michael. After 12 months the surface was still excellent and I hadn't touched it other than vacuuming and wiping with a cloth. They mention that applying their carbon glide product...
  2. Replies
    18
    Views
    2,532

    Gordon, I mark a line on the inside of one joint....

    Gordon, I mark a line on the inside of one joint. On the edge mortises I hold/clamp the stock horizontally against the fence and with the matching mortises on the face I hold the stock vertically...
  3. I contacted Sawstop with a run out of 0.009" and...

    I contacted Sawstop with a run out of 0.009" and they said that was within tolerance and the cut was smooth and straight. I adjusted it to 0.004" and the quality of cut remained the same, so I think...
  4. Replies
    18
    Views
    2,532

    I've also made my own but ended up buying the...

    I've also made my own but ended up buying the Veritas version for more accuracy and repeatability. Great for small boxes and picture frames that I frequently make.
  5. I use these .......

    I use these .... https://armor-tool.com/product/auto-adjust-p7-hh-horizontal-dog-peg-clamp/ (small rod) and these .......
  6. Replies
    31
    Views
    2,577

    Or this .........

    Or this ...... https://www.eztension.com/buy-one-now/eztension-bandsaw-tension-gauge

    I originally thought this was a gimmick but it does the job and gives similar results to using the more...
  7. I bought these (...

    I bought these ( https://www.kregtool.com/shop/routing/routing-system-components/corner-routing-guide-set/PRS1000.html )last year and they work well. I also couldn't be bothered making them.
  8. Replies
    39
    Views
    7,506

    The Incra LS TS fence system is more accurate,...

    The Incra LS TS fence system is more accurate, more repeatable, adjustable to a 1000th of an inch and less expensive.
  9. Replies
    18
    Views
    5,289

    I've tried all 3, T Track, T slot and dovetail...

    I've tried all 3, T Track, T slot and dovetail for years and have never had a problem with strength (damage) from any of them other than T-track lifting if not secured properly particularly with Kreg...
  10. Replies
    18
    Views
    5,289

    Where I come from I pay less than $10USD for...

    Where I come from I pay less than $10USD for 900mls (about 3 feet) for T Track which is not expensive but like dovetail slots you can also use a T-slot router bit and then you don't have to buy...
  11. Replies
    17
    Views
    4,111

    I've used Colliflower inserts but not anymore...

    I've used Colliflower inserts but not anymore after the brake was triggered making a bevel insert. Wasn't impressed. After complaining I was kindly offered a replacement but that never eventuated. I...
  12. I have the original system where you attach your...

    I have the original system where you attach your own gauge using a self made adapter. I nearly fell off my chair when I saw the price of $59.99. Low price and Woodpeckers are not normally in the same...
  13. When the stock is long and can possibly lift...

    When the stock is long and can possibly lift upwards while I'm cutting and when my fingers are too close to the blade. Extra wide stock I often use clamps. Repetitive cuts that aren't too small I...
  14. Replies
    18
    Views
    5,289

    Yes T-slot is a great solution which gives the...

    Yes T-slot is a great solution which gives the same functionality as T-track with the only cost being a suitable router bit. You can even make a T-slot by carefully arranging stacked boards.
  15. Replies
    18
    Views
    5,289

    I'm in the only T Track camp. Firstly you can use...

    I'm in the only T Track camp. Firstly you can use all the auto adjust clamps from Rockler, Bessey, Kreg and Armor tool as well as home made and cheaper clamps . They all swivel at 360 degrees and as...
  16. Replies
    10
    Views
    1,410

    When using the table saw and the I Box jig I only...

    When using the table saw and the I Box jig I only needed to hold the stock by hand to keep it secure but on the router table I found I needed to clamp as the router bit tends to lift the stock. This...
  17. Just over 1/8" but you can always use a stop...

    Just over 1/8" but you can always use a stop block and a clamp if wanting to cut less than 1/8"
  18. Arrived a week ago and for an unbelievably low...

    Arrived a week ago and for an unbelievably low cost item from Woodpeckers, it works well. The first thing I did was check that the fence was straight and then made an interface board to fit the V120....
  19. I also have the Lee valley version (...

    I also have the Lee valley version ( https://www.leevalley.com/en-gb/shop/tools/power-tool-accessories/114883-veritas-domino-joinery-table?item=05J1701 ) and love it. I make small boxes and small...
  20. I was using something similar to the Powertec on...

    I was using something similar to the Powertec on my Incra V120 gauge which worked well until I saw the Woodpecker fence and fell off my seat when I saw the price so instantly ordered. I really like...
  21. Have you seen Woodpeckers fence for mitre gauges?...

    Have you seen Woodpeckers fence for mitre gauges? Seems like an inexpensive (strange saying that for Woodpeckers) workable solution.
    https://www.youtube.com/watch?v=_glkKhwW3U8&t=5s
  22. Thanks Derek. Nice to hear from an actual user. I...

    Thanks Derek. Nice to hear from an actual user. I contacted them about reapplying and they said, remove dust then a couple of coats and your done. No need to strip back unless something unforeseen...
  23. Couldn't resist any longer and ordered the kit....

    Couldn't resist any longer and ordered the kit. Yes it was expensive particularly the delivery charge to Australia, but if it produces what they say it does then its worth it. I'll report back once...
  24. I thought I'd get some comments about its expense...

    I thought I'd get some comments about its expense and how wax works just as well etc etc and these are fair points but I was just after information on this product. One benefit, I see, is the coating...
  25. Carbon method for rust prevention - any good?

    I normally clean my Sawstop with WD40, then apply Boshield T9 and finally paste wax and this has been OK but not as good as I would like.

    I saw this video (...
Results 1 to 25 of 153
Page 1 of 7 1 2 3 4