Search:

Type: Posts; User: Ruperto Mendiones; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    573

    9 mm router bits

    I am a hobbist woodworker. Recently I have been making boxes of 9 mm plywood.

    While I can make tight fitting dados with my dado stack, there are many times I would prefer to use my router...
  2. Forrest Dado King. Slightly OT I lost a tooth...

    Forrest Dado King. Slightly OT I lost a tooth in a sawstop stop block. Forrest was able to repair the tooth and re-grind the set. works like new
  3. Replies
    5
    Views
    1,201

    Digital /angle Gauges

    Recently I found i had difficulty matching a stair stringer angle to my miter gauge. The little Wixey cube angle gauge read out tenths of a degree but I had difficulty matching the readout to a...
  4. If you can wait for a custom blade: Carbide...

    If you can wait for a custom blade: Carbide Processors glue joint rip blade:
    10" Dia., Grind: GR (Triple Chip Grind; 22deg Hook), 30 Teeth, 0.094" Plate, 0.145" Kerf, 0.625" Arbor. $95
  5. Replies
    4
    Views
    923

    I thought smelled a rat.

    I thought smelled a rat.
  6. Replies
    4
    Views
    923

    Dewalt pricing ?

    I googled the Dewalt 735 planer as I needed to know the weight of it. I came across a website "Dewaltlii". A new DW 735 planer was offered for ~$100. Parts appeared at similar discounts. All of...
  7. Replies
    18
    Views
    2,319

    An alternate means would be to buy a tank of...

    An alternate means would be to buy a tank of nitrogen to inflate the tires. Until I got the motorhome, the compressor serviced all my needs easily.
  8. Replies
    18
    Views
    2,319

    compressor pressure reset

    I have a Ingersoll Rand ~ 2 hp hp 80 gal tank air compressor. The setpoints are 120 psi shutoff and 80 psi turn on. Unfortunately my motorhome tires need 100 psi. When I can't get air into a...
  9. Replies
    72
    Views
    17,136

    5* on wolf induction cooktop--or any good...

    5* on wolf induction cooktop--or any good induction one. Ours is faster than gas or resistance electric; the surface is easy to clean and, considering the short time-to-boil intervals, probably no...
  10. Replies
    3
    Views
    1,891

    Bob Marino retiring

    Bob Marino is retiring and is company is no longer the same.

    Last night I entered an online order c Bob Marino's best tools. The address I entered had a mistake. I attempted to correct it and...
  11. Replies
    23
    Views
    4,467

    Custom orthotics or semi-custom [Dr Scholls etc]...

    Custom orthotics or semi-custom [Dr Scholls etc] might make red wing the ticket--at least it works for me.
  12. Replies
    26
    Views
    2,758

    I can't suppress the internist in me... First off...

    I can't suppress the internist in me... First off a detailed history and physical reviewing usual medications, previous illness, habits and, since we are speaking to a geriatric patient--water...
  13. Replies
    67
    Views
    13,193

    Yes, exercise and avoiding SUGAR white potatoes...

    Yes, exercise and avoiding SUGAR white potatoes and grains [particularly white ones] will take off weight and improve health. [and I say that from both personal observation and the perspective of a...
  14. Since MDF is mentioned, step drills for confirmat...

    Since MDF is mentioned, step drills for confirmat screws might partially fulfill the op's search. Hafele and Rockler have their own versions--at opposite extremes of the budget.
  15. How about good old fashioned water filters and a...

    How about good old fashioned water filters and a softener--perhaps supplying only your sink?
  16. I don't know about refrigerating bottled food's ...

    I don't know about refrigerating bottled food's storage life but I do know that "use by" dates are quite arbitrary. Consumer reports mentioned this a few months ago. Sauces...I'd be inclined to...
  17. I guess setting the fence on a router table is...

    I guess setting the fence on a router table is the best way to cut an exact fit rabbet. I wondered if anyone had used a bearing guided rabbeting bit and bought bearings sized to cut the exact...
  18. Rabbeting bits sized for baltic birch plywood

    Is there a rabbeting router bit set sized for baltic birch ply thicknesses? Alternatively has anyone purchased individual bearings to achieve the same? Using imperial sized bearings I get an...
  19. What about 100ll aviation gasoline? There is at...

    What about 100ll aviation gasoline? There is at least some lead in it.
  20. Rogerssystems.com have the greatest gamut of...

    Rogerssystems.com have the greatest gamut of adapters I've found.
  21. Replies
    24
    Views
    4,630

    Since we are talking planes and chisels... a good...

    Since we are talking planes and chisels... a good sharpening kit is essential. Scary sharp, oilstones, waterstones..which matters less than having a good set and learning to use it.
  22. Replies
    43
    Views
    9,528

    I, too, take great issue with misspellings and...

    I, too, take great issue with misspellings and faulty grammar--in some instances the meaning of the author is obscured. But I still delight in applying the break to slow my bandsaw down. :)
  23. Replies
    48
    Views
    8,858

    Tormek with their knife jig. Keeps a better edge...

    Tormek with their knife jig. Keeps a better edge than I could do by hand alone.
  24. I ordered a flat top 1/8" kerf blade from Carbide...

    I ordered a flat top 1/8" kerf blade from Carbide processors. Works great.
  25. Where do you buy hand and car tools-- not in sets

    Where do you tool-shop now that Sears is fading away?


    I have always shopped at Sears when I needed a hammer, pliers or the odd size socket, extension bar. or other tool not part of a set.
    ...
Results 1 to 25 of 169
Page 1 of 7 1 2 3 4