Search:

Type: Posts; User: Dwight Rutherford; Keyword(s):

Page 1 of 16 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    629

    Good choice! Been using mine for 12+ years....

    Good choice! Been using mine for 12+ years. Recommend using a camera instead of the laser. PM me if you wish.
  2. Replies
    9
    Views
    629

    Just checked it out, doesn’t appear to be able to...

    Just checked it out, doesn’t appear to be able to hollow to the depth you want, but have no personal experience with it. Take a look at the Jamiesom , Sinner, and Carter set ups. They are all rock...
  3. Replies
    9
    Views
    629

    I’m not familiar with the Transformer system. Is...

    I’m not familiar with the Transformer system. Is it a captured bar rig or articulated?
  4. Replies
    9
    Views
    629

    If you want to deep hollow up to 16” I recommend...

    If you want to deep hollow up to 16” I recommend a captured bar rig like the Jamieson or Sinner systems. They both accommodate 1 1/4” and 1 1/2” boring bars which won’t vibrate when going deep....
  5. Replies
    1
    Views
    648

    Nice looking!

    Nice looking!
  6. I changed to a camera set up after 10 years with...

    I changed to a camera set up after 10 years with a laser. So much better!
  7. Replies
    24
    Views
    2,365

    What is the air pressure at the ROS? Are you...

    What is the air pressure at the ROS? Are you pressing the sander against the wood with much pressure?
  8. Replies
    18
    Views
    1,547

    I have always tightened both sockets six or more...

    I have always tightened both sockets six or more times. Still loosens. My Vicmarc’s don’t loosen.
  9. Replies
    18
    Views
    1,547

    The one I have doesn’t have a set screw. Drilled...

    The one I have doesn’t have a set screw. Drilled and tapped it myself.
  10. Replies
    18
    Views
    1,547

    The jaws are interchangeable. My complaint is...

    The jaws are interchangeable.
    My complaint is the chuck loosens frequently when in use. Have to continually stop, check and tighten.
    Next time I’ll just bite the bullet and buy another Vicmarc.
  11. Replies
    18
    Views
    1,547

    These chucks are Vicmarc clones. Yes you can do...

    These chucks are Vicmarc clones. Yes you can do indexing.
  12. Replies
    2
    Views
    546

    I have a Baldor slow speed grinder with CBN...

    I have a Baldor slow speed grinder with CBN wheels. Took the guard off and run it that way. Not a problem. I think the main reason grinders come with guards is to protect the operator in the event...
  13. Replies
    12
    Views
    845

    I only drill about an inch at a time, withdrawing...

    I only drill about an inch at a time, withdrawing the bit to clean it and allow it to cool down. Also drill at 500 rpm to keep the heat down. Fast rpms and deep drilling make for wood expansion.
  14. Replies
    30
    Views
    4,171

    Teflon tape has always worked for me.

    Teflon tape has always worked for me.
  15. Replies
    4
    Views
    858

    I would contact them here; Trend Routing...

    I would contact them here;
    Trend Routing Technology Inc.
    7351 West Friendly Ave
    Greensboro, NC 27410
    or
    www.trend-USA.com
    or
    877-918-7363
  16. Replies
    18
    Views
    1,591

    I donít think so. Iíd bite the bullet and buy a...

    I donít think so. Iíd bite the bullet and buy a new one. Try Bandsawsdirect they carry Lennox blades.
  17. Replies
    30
    Views
    4,171

    I have a California Air compressor that I’m very...

    I have a California Air compressor that I’m very pleased with.
  18. Replies
    31
    Views
    3,175

    Yes it does.

    Yes it does.
  19. Replies
    31
    Views
    3,175

    I use an Armorline RP77321 plumbers slip nut...

    I use an Armorline RP77321 plumbers slip nut wrench. Got it on Amazon for $13.
  20. Ricc, I used a laser on my Jaimeson rig for...

    Ricc,

    I used a laser on my Jaimeson rig for about 10 years, switched over to a camera 3 years ago. Here are some thoughts about the difference.

    When using the laser, the red dot is only showing...
  21. Replies
    17
    Views
    1,371

    The actual part number of the electrical switch...

    The actual part number of the electrical switch is ZB2-BE102. Use that to search E-Bay.
  22. Greg, my offer of supplying the measurements...

    Greg,
    my offer of supplying the measurements still stands. Tried to send a PM but was blocked.
    contact me
    dwightrutherford@hotmail.com
  23. Replies
    17
    Views
    1,371

    The complete switch can be ordered on E-Bay for...

    The complete switch can be ordered on E-Bay for about $10. The electrical portion is about $7.
  24. Replies
    17
    Views
    1,371

    What does the VFD read? The problem could also be...

    What does the VFD read? The problem could also be the potentiometer (speed dial). An electrician with a multimeter should be able to determine where the problem is. If you need to replace the switch...
  25. Replies
    11
    Views
    990

    I have been using a Harbor Freight 3/8” variable...

    I have been using a Harbor Freight 3/8” variable speed close quarters drill for years. $30.
    https://www.harborfreight.com/38-in-variable-speed-reversible-close-quarters-drill-60610.html
Results 1 to 25 of 388
Page 1 of 16 1 2 3 4