Search:

Type: Posts; User: Charlie Jones; Keyword(s):

Page 1 of 13 1 2 3 4

Search: Search took 0.23 seconds.

  1. Replies
    38
    Views
    2,424

    I have dust collection. I vac off anything on the...

    I have dust collection. I vac off anything on the bench or machines at the end of my work session as well as anything on the floor nearby. Prior to starting a new project I vac the whole shop as...
  2. Replies
    14
    Views
    903

    Good job. You are to be commended for tacking a...

    Good job. You are to be commended for tacking a project like that right from the start. My advise, read and do, read and do, at some point you will notice a profound shift to a higher skill level in...
  3. Replies
    20
    Views
    2,072

    Beautiful wood and beautiful work.

    Beautiful wood and beautiful work.
  4. Replies
    16
    Views
    1,524

    Nice craftsmanship Bill. A good design to. I like...

    Nice craftsmanship Bill. A good design to. I like the figure.
  5. Replies
    17
    Views
    2,239

    Beautiful table Tony. I love the simplicity. Your...

    Beautiful table Tony. I love the simplicity. Your doing a great job. Better use a tough finish on the base. People will put their feet on it.
  6. I have been using TB 3 for a couple of years. I...

    I have been using TB 3 for a couple of years. I have not had any failures. After reading this thread I decided to test it by breaking some 3/4 cherry with hammer strikes along the glue lines. The...
  7. Replies
    41
    Views
    2,586

    I use my finger to. At least up to now. I just...

    I use my finger to. At least up to now. I just got one of the new silicone glue brushes from Klingspor. Now I just let the glue dry and pull it off (PVA). I also use old credit cards for spreading on...
  8. Replies
    34
    Views
    2,273

    I switched my Clear-Vue to venting outside last...

    I switched my Clear-Vue to venting outside last year. I haven’t noticed any dust coming out the vent. It is blowing into the woods behind the shop.I wish I knew that when I installed the system. I...
  9. Replies
    13
    Views
    1,260

    Nicely done

    Nicely done
  10. Replies
    14
    Views
    1,388

    WOW. That is an awesome design and beautiful...

    WOW. That is an awesome design and beautiful wood. I especially like the Claro one.
  11. Replies
    12
    Views
    5,297

    Let us know how it works out. I may get one to...

    Let us know how it works out. I may get one to supplement my cast iron 6".
  12. Replies
    8
    Views
    1,245

    Very Nice work. The figure is spectacular.

    Very Nice work. The figure is spectacular.
  13. Replies
    20
    Views
    2,005

    Fine work Mark. That chair took a lot of...

    Fine work Mark. That chair took a lot of work,skill and patience. Congratulations.
  14. Replies
    17
    Views
    2,307

    Now I like that illustration. Sometimes you just...

    Now I like that illustration. Sometimes you just have to start over.
  15. Very impressive. A great addition to your home.

    Very impressive. A great addition to your home.
  16. Replies
    7
    Views
    751

    That looks like a lot of work. Very nice job.

    That looks like a lot of work. Very nice job.
  17. Replies
    7
    Views
    558

    Thanks Mike. I will check them out.

    Thanks Mike. I will check them out.
  18. Replies
    7
    Views
    558

    Thanks Guys. I think I will use these rolls for...

    Thanks Guys. I think I will use these rolls for hand sanding and buy the pre cuts for the Supermax. This is a fine machine and I wouldn’t want to mess it or the wood up. This is a great forum.
  19. Replies
    7
    Views
    558

    Maybe I wasn’t clear. I will not convert the...

    Maybe I wasn’t clear. I will not convert the drum. I would cut the paper to fit and use up the hook and loop stuff I already have.
  20. Replies
    7
    Views
    558

    Hook and loop on Supermax

    I just bought a new SuperMax drum sander. I have a bunch of hook and loop rolls left from my old sander. Can I cut these and use them on the SuperMax. Has anyone of you done this?
  21. Replies
    13
    Views
    1,458

    Very nice ladder. You do good work.

    Very nice ladder. You do good work.
  22. I love using old wood. The end result can be far...

    I love using old wood. The end result can be far better or worse than planned. That puts adventure into the build.
  23. Replies
    22
    Views
    1,462

    I forgot to add my Clear Vue cyclone. I bought it...

    I forgot to add my Clear Vue cyclone. I bought it back when Ed Magano owned the company. He heated the plastic in an old range and wrapped it around a wooden form. He has a home made C and C router...
  24. Replies
    22
    Views
    1,462

    Machine diversity

    I was looking around the shop today and realized that most of my machines are different brands. I have a Unisaw, Woodtek jointer, Grizzly planer, Laguna bandsaw, Delta lathe, Rikon belt disc sander,...
  25. Replies
    21
    Views
    2,101

    My last sled was 3/4 with a heavy oak fence. It...

    My last sled was 3/4 with a heavy oak fence. It worked great. I just built a 1/2 of Baltic Birch ply. I used 3 layers of 1/2 Baltic Birch ply for the fence.ay last sled had red oak runners and they...
Results 1 to 25 of 315
Page 1 of 13 1 2 3 4