Search:

If you remove the top cover you will see two set screws with locking nuts on the orange chip breaker. Loosen the nuts and tighten or loosen the screws to adjust the breaker.

There are going to be some clunking noises as you raise and lower the table as it is propelled by a chain drive system. You just want to make sure it is well lubricated and should be from the...

I had the Veritas medium and actually sold it to get the large (cyber monday deal). Don't regret that at all as its more comfortable to use two handed if need be and has a blade width approaching...

A No.3 can be easier to push especially if your using a high angle frog. I love my HA#3 Lie Nielsen on tougher or figured woods for just this reason.

Ive seen them available from the place Julie mentioned and Spectrum Supply, which is where I got mine. The cost is only slightly more then a Woodslicer but being bi metal will last a lot longer. I...

Im running a 1" Woodmaster B on my 513 and like it a lot. Its 1.3 tpi and just eats wood. i think it comes in 2 as well which would still be a fast cut but likely a bit smoother in all respects.

How did you guys transition from the inlet to your ductwork? Im hoping to use 6" PVC s&d. Does the outer diameter of this stuff correspond with the inner diameter of the inlet? or perhaps the bell...

Typically a 170 degree open hinge would be used in this case. It mounts flat to the inside of the blind panel.

http://www.leevalley.com/en/Hardware/page.aspx?p=55472&cat=3,41241,55420

Not that im an expert but i installed 3/4 emt for my 10g run of nmd90 as it was recommended to me.

Giant hassle for sure... I just store mine in deep drawers which keeps them out of the way but I can get to them quick. Cases go in the rafters if I were to sell anything.

I agree 8 gauge is overkill. Someone must have just used what they had on hand but that stuff is hard to work with in tight spaces. Motor draw is rated at 17.9 amps. Its a Brooks motor and the...

Heres a shot in the dark but does anyone have any insight into how this would be correctly wired? Im resisting calling in a pro because I think it is fairly simple but haven't ruled it out. Im...

Thanks guys. This was my first kick at the can so I was pleased with how it turned out.

Picked this for $25. It was in decent shape, not too rusty and all the parts were there.

However the tote was broken in half so I shaped a new one and turned a knob to match. With the new Veritas...

Thanks Derek. I had a feeling this was the case but I just wanted to see if I could get away with it. I might still give it a whirl for its intended purpose alone.

I dont know how many here have or have had experience with one of these but I was wondering about the level of clamping effectiveness when only the top half of the vise is used ie. when edge planing...

I put link belts on my older unisaw and after having regular belts it is oh so smooth, especially in colder temps. I just made sure I had the same number of links on each belt. Some may say this is...

I got the same planer this summer and my first impressions mirrored yours. A year earlier I had purchased a 17" bandsaw from them and its fit and finish was pretty much flawless. In contrast the...

In smaller pieces you can stick them in a wooden holder, file/grind different profiles into it and boom, instant cheapo beading tool. Works great.

I would say that not having the mounting holes for the screws isnt a big deal as long as it IS a tight fit in the table insert with no side to side play. Even minimal movement could be a problem...

Shimmed the outside bottom edge of the bracket. It took six layers of masking tape but I got it almost perfectly flat and the fence no longer lifts up when locked. If anyone else has this problem...

I took the rail tube off and checked the L bracket for squareness. At certain areas along its length it is but in others it is very much out of square (obtuse), more than an 1/8th over 2 1/2 inches....

Both sides of the rail are machined on my setup. While aligning the fence to the mitre slot I found that one set screw had to be several turns tighter then the "other". The "other" screw is just...

No template but the rail is set at the specified height. Is there a way to adjust the pressure required to lock the fence down? The only way I can see is if you back off the alignment set screws...

I didnt think it was normal for it to lift but this is my first direct experience with a beise style fence. The problem is only when actually locking it down. once its locked it stays firm. The...