Search:

Type: Posts; User: Bill Dufour; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.36 seconds; generated 56 minute(s) ago.

  1. unexceptable. I am surprised a Starret left the...

    unexceptable. I am surprised a Starret left the factory that far off. Mitutoyo. or old lufkin, brown and sharpe, Fowler, Scherr Tumico probably others i am forgetting.
    BilL D
  2. Replies
    27
    Views
    1,204

    Duct seal stiff brush or putty knife. BilL D

    Duct seal stiff brush or putty knife.
    BilL D
  3. Replies
    3,499
    Views
    871,271

    Sticky: A priest, a minster, a Rabi and an Imam are on a...

    A priest, a minster, a Rabi and an Imam are on a small plane, with only three parachutes, that is heading west. It crashes on the US Canada border. Where are the survivors buried?
    Bill D.
  4. Replies
    9
    Views
    311

    Reminds me of the old joke about a small plane...

    Reminds me of the old joke about a small plane crashed into a cemetery. The count is over 100 dead, they are still digging up bodies.
    Bill D
  5. Replies
    5
    Views
    350

    To be clear, you have the fan and fan housing? If...

    To be clear, you have the fan and fan housing? If so buy a bag or two and hang it on the wall.
    BilL D
  6. Replies
    27
    Views
    1,204

    Dynamic balancing is done with the wheel off...

    Dynamic balancing is done with the wheel off placed onto a machine. The wheel is spun up to some speed and smoke and mirrors figure out where to place weights to get it balanced. used by most...
  7. Replies
    27
    Views
    1,204

    Grafting seal is very similar to water based...

    Grafting seal is very similar to water based roofing tar. Truck bed lining is possible as well.
    Bill D
  8. Replies
    11
    Views
    543

    I have heard of using segments of horizontal...

    I have heard of using segments of horizontal milling cutters or slitting saws, carbide toothed. Have to weld them to an old blade to attach to the machine. Do they make e wood circular blade small...
  9. Replies
    27
    Views
    1,204

    My little mill/drill had a sheet metal guard...

    My little mill/drill had a sheet metal guard vibrate like crazy. I was going to paint it inside with grafting seal to soak up the vibration. I stuck a free harbor fright magnetic parts tray on the...
  10. Replies
    39
    Views
    2,221

    Words to make the count Bil lD

    Words to make the count
    Bil lD
  11. California has required all roof replacements or...

    California has required all roof replacements or new roofs to be cool roofs for several years they reflect more solar gain then standard colors. This includes black cool colors.
    BilLD
  12. Replies
    16
    Views
    940

    Growing up we had a pry bar about one inch...

    Growing up we had a pry bar about one inch diameter 5 feet long. point on one end bent flat on the other. Story is it was an axle shaft from a cement truck. Very similar to the Horrible Fright one...
  13. Replies
    16
    Views
    940

    Toe Jack, machine skates. Bill D

    Toe Jack, machine skates.
    Bill D
  14. Replies
    3,499
    Views
    871,271

    Sticky: My brother had the chemistry set with a red...

    My brother had the chemistry set with a red plastic volcano. Put baking soda and vinegar in the crater and plug in the white snow capped peak and wait for it to fly and hit your eye.
    After that he...
  15. Don't ride a bike while holding a wood chisel. ...

    Don't ride a bike while holding a wood chisel. You might get tackled?
    Bill D
  16. Dupont chain saver lube. Wax in a spray can. ...

    Dupont chain saver lube. Wax in a spray can. Goes on wet with solvent that cleans off gunk. Dries to a clear thin wax that does not attract dust.
    Bill D
  17. Motorcycle shop? BilLD

    Motorcycle shop?
    BilLD
  18. Replies
    13
    Views
    752

    Peen or shot blast the tip to make it rougher and...

    Peen or shot blast the tip to make it rougher and hold oil.
    BilLD
  19. Replies
    13
    Views
    752

    I drilled a few very small holes in one dipstick....

    I drilled a few very small holes in one dipstick. Think pin vise #60-80. Notches on the side are also used. A good dipstick is cross hatched to help see the oil.
    BilLD
  20. Replies
    3,499
    Views
    871,271

    Sticky: My wife has the shirt... Irony, the opposite of...

    My wife has the shirt... Irony, the opposite of Wrinkly.
    BILL D
  21. Replies
    6
    Views
    684

    Now the problem is everything downstream of the...

    Now the problem is everything downstream of the pump is contaminated with oil. The tank, valves, hoses, plumbing, filters, regulators. No idea how clean you need your air. Most of the oil will...
  22. Replies
    7
    Views
    843

    Predrill the corners. Make a jig of plywood with...

    Predrill the corners. Make a jig of plywood with four threaded rods sticking up at the corners. Rods are a good bit smaller then the holes for quick assembley. Put glue on the ends of the sticks...
  23. Replies
    15
    Views
    1,091

    Source for power adjustment hand cranks.

    People ask how to power the planner adjustment, saw rise and fall, drill press table, etc. I just found out today about truck tarp gearmotors.
    twelve volts dc, 50-100 rpms, 1/2 hp or so, 3/4"...
  24. Lucille Ball asks for the rights to reruns to I...

    Lucille Ball asks for the rights to reruns to I love Lucy. The network was like who wants to see old shows. She got the rights for free but she had to pay to buy the machines to record them.
    Lucas...
  25. Replies
    13
    Views
    1,035

    Boeing should have checked those bolts. My 1974...

    Boeing should have checked those bolts. My 1974 Plymouth had four big bolts holding the main front suspension K member to the frame. One of the four was missing when I looked after owning the car...
Results 1 to 25 of 498
Page 1 of 20 1 2 3 4