Search:

Type: Posts; User: Lee Schierer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.27 seconds.

  1. Replies
    16
    Views
    1,226

    The good news is the two long pieces can be...

    The good news is the two long pieces can be reworked to make the short sides and you only need new material for the long front and back. You also have two short pieces for another project or for...
  2. Replies
    5
    Views
    469

    First off, since you are in Alaska and there are...

    First off, since you are in Alaska and there are earthquakes there I would suggest that you tie the shelves to the wall.

    we used to lots of canning, but have tapered off now. I built the shelves...
  3. Replies
    7
    Views
    776

    When I align my older Craftsman cast iron table...

    When I align my older Craftsman cast iron table saw, I align the blade to the left miter slot. Then I align the fence to the same miter slot with the dial indicator mounted on my miter gauge. I...
  4. Replies
    6
    Views
    502

    You probably also gave him a ball peen hammer to...

    You probably also gave him a ball peen hammer to drive them with.:D
  5. Replies
    3
    Views
    353

    My SIL was the same way. One year he came to our...

    My SIL was the same way. One year he came to our house for Christmas and he needed a gift our daughter (his wife). He wanted to make something. We went out in the shop with just a few days before...
  6. Replies
    9
    Views
    1,178

    Most windows computers have a snip app that lets...

    Most windows computers have a snip app that lets you make a jpg of anything displayed on the screen.
  7. Replies
    6
    Views
    489

    Very nice an Heirloom for sure. The top is...

    Very nice an Heirloom for sure. The top is really a nice piece of wood.
  8. Replies
    49
    Views
    2,486

    Here is a link to the specifications for a Galaxy...

    Here is a link to the specifications for a Galaxy Z Flip2 5Gb

    I casually looked at one a while back at the AT&T store and wondered how long before the folding screen fails.
  9. Replies
    14
    Views
    900

    The Freud Glueline rip blade has flat top teeth...

    The Freud Glueline rip blade has flat top teeth and TCG and is reasonably priced. Half of the teeth are flat top half are TCG. It gives a nice flat bottom kerf and a smooth sidewall cut.
    481561
  10. Replies
    4
    Views
    487

    Make a filler out of maple that will fit in the...

    Make a filler out of maple that will fit in the wide kerf. Glue that filler in place and make your new cut once the glue cures completely.
  11. Replies
    7
    Views
    1,014

    You are listed as a Member, if this is not...

    You are listed as a Member, if this is not correct, please contact Keith Outten.

    Only contributors can send personal messages through the system. Becoming a contributor costs a minimum of $6...
  12. Replies
    12
    Views
    861

    Really nice job. I like the color and the nice...

    Really nice job. I like the color and the nice finish.
  13. Replies
    14
    Views
    844

    All have been deleted without opening them......

    All have been deleted without opening them......
  14. Replies
    17
    Views
    2,048

    The donate button does show up in full site mode...

    The donate button does show up in full site mode on tablets and phones.
  15. I converted a closet into a pantry for my wife. ...

    I converted a closet into a pantry for my wife. I used full extension soft close slides rated for 100 pounds.
    481348481346 481347
    The shelves are made with poplar frame, red oak front panel and...
  16. Just be sure to apply your glue to both sides of...

    Just be sure to apply your glue to both sides of the joint.

    You need to make or buy a clamping set up like this. You don't need to fill in all four pieces, you can glue up just two at a time,...
  17. Thread: bee trap

    by Lee Schierer
    Replies
    10
    Views
    923

    Nothing other than size and it is up in a tree.

    Nothing other than size and it is up in a tree.
  18. Replies
    8
    Views
    782

    I had suggested a cloth covering but it was...

    I had suggested a cloth covering but it was rejected.

    Just a note those soft fiber bulletin boards start to fail if you place too many tacks or push pins in the same area.
  19. Replies
    14
    Views
    844

    Annoying spam

    For the past week we've been receiving supposed emails from McAfee saying our subscription is about to expire. Sometimes we get two or three per day. Today we started getting the same bogus notices...
  20. Thread: Firefox

    by Lee Schierer
    Replies
    12
    Views
    901

    I'm running Firefox 101.0.1 on windows 11 with no...

    I'm running Firefox 101.0.1 on windows 11 with no issues.
  21. Replies
    8
    Views
    782

    Lessons learned working with cork

    I was asked to make a couple of bulletin boards to go on the back of some doors in the church welcome center. The deign called for two 18 x 24 framed cork boards. I was able to order the 3/8" x 24"...
  22. Replies
    20
    Views
    887

    That is a nice set up and the price is good. Be...

    That is a nice set up and the price is good. Be careful measuring from the sides of the teeth, because most are have a relief grind on the sides which can lead to errors.

    Switch you gauge to the...
  23. Replies
    1
    Views
    386

    I would say you were successful....

    I would say you were successful....
  24. Replies
    20
    Views
    887

    Are you measuring off the side of a tooth or the...

    Are you measuring off the side of a tooth or the blade plate when you make these parallel measurements.

    I put a mark on a point close to a tooth with a magic marker. I rotate that point from...
  25. Replies
    20
    Views
    887

    From your photo, it looks like the back teeth of...

    From your photo, it looks like the back teeth of the blade is dragging on your wood based on those curved grooves on the cut edge.
    481144
    I would check the alignment of the blade to the miter slot...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4