Search:

Type: Posts; User: William Hodge; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    361

    You can sometimes pay extra, and have it...

    You can sometimes pay extra, and have it delivered to a residence in a truck with a lift gate. That is, if your road accepts trucks.
  2. This is climb cutting power return on a roughing...

    This is climb cutting power return on a roughing jointer. For rough edge jointing big wood (8/4 x 10" x 8') prior to rough ripping, the cutter head brings the wood back for a second pass. Knife and...
  3. This is the part that I need. ...

    This is the part that I need.
    https://sawmillcreek.org/images/part_p_112180_2423021586.jpg ...
  4. Good idea. I'm getting a new feeder from...

    Good idea.
    I'm getting a new feeder from Grizzley. If the parts look the same, I'm going to buy an $85. motor control from Grizzley.

    I wish that there were a forum out there dealing with Asian...
  5. Thank you for the information. I'm going all in,...

    Thank you for the information. I'm going all in, where no man has gone before.

    By looking up Co-Matic, I found that Grizzley sells the complete motor control assembly for $86.00. It's worth it to...
  6. Delta Baby Feeder Circuit Board Replacement

    456927

    The circuit board on this feeder is not working, and new ones are not available. Do the Grizzley circuit boards work in this feeder?
  7. Replies
    35
    Views
    1,977

    OP, the one piece of advice I have for you is to...

    OP, the one piece of advice I have for you is to skip any micro bevel, or whatever it's called. Just make an edge, and use it.

    I use 200 DMT and 800, 1200, and 6000 grit water stones, free hand....
  8. Replies
    19
    Views
    932

    If the buyer gets hurt while loading a machine on...

    If the buyer gets hurt while loading a machine on their vehicle while on your property, are you liable?
  9. Replies
    11
    Views
    1,069

    If you have allergy problems, it would be a good...

    If you have allergy problems, it would be a good idea to put the cyclone and dust barrel outside of your work space. Dumping the barrel out is a dusty job. If the barrel fills up, that disaster will...
  10. Replies
    21
    Views
    1,900

    I have had a few hits. I could tell some stories...

    I have had a few hits. I could tell some stories about lightning hits, but most of them are made up. However, this is not the forum where one describes extramarital affairs uncovered by untimely...
  11. Replies
    10
    Views
    632

    Old machine parts for long lived machines can get...

    Old machine parts for long lived machines can get stored in the bottom of the machine. The next user might want them.

    I have square cope heads I replaced with corrugated back knife heads. The old...
  12. I'm sorry to hear about the difficulty in running...

    I'm sorry to hear about the difficulty in running oak. It sounds like you're running clean wood.

    I only have ever taken 1/32" off at a time, all Sapele. I have to wax the beds with paraffin and...
  13. What are you running through the planer? I...

    What are you running through the planer?

    I have had a 735 for nine moths, and I have run about 1000 board feet of lumber through it, two faces. All the wood has gone through my rough planer first....
  14. Replies
    7
    Views
    727

    Check for broken castings and impact marks in the...

    Check for broken castings and impact marks in the paint. If someone has hoisted a jointer by its tables, or dropped it, the dovetails where the tables attach to the base can be cracked.

    The gib...
  15. Replies
    26
    Views
    1,796

    If you are working in marginal conditions, it...

    If you are working in marginal conditions, it would be good to get a marginal conditions work bench. It would be like buying a Tesla when you live on a long gravel road, like I do.

    A show piece...
  16. I like the teaser where Sam Blasco pushes the...

    I like the teaser where Sam Blasco pushes the wood with his thumb on the tail end of the board. It's kind of like watching a lion tamer show, where you hope that the guy in the cage with the lions...
  17. To use a European type guard, use push pads.This...

    To use a European type guard, use push pads.This allows you to push down on the wood on the outfeed table.

    Start the wood in to the cutter, face 12". Reach over the guard, and push the wood down...
  18. Replies
    16
    Views
    1,361

    An old guy I worked with said "Never lift a...

    An old guy I worked with said "Never lift a planer by its lady parts."

    The feed rollers are spring loaded. Hoisting here would be by the cutter head, and the head assembly.

    The machine...
  19. Replies
    4
    Views
    635

    I have a little blower like that for small demand...

    I have a little blower like that for small demand machines. Shutting the blower off when you don't need it helps. I use a Long Ranger switch on my tool belt. I don't worry about short cycles.
    ...
  20. Replies
    16
    Views
    893

    If this is for your house, you could try...

    If this is for your house, you could try laminating it.

    Hollow out the stile, insert a 3/16" piece of wood in it with Titebond 3, and clamp it flat. Titebond 3 sets up a little slower than...
  21. I have a Dewalt 735 as a finish planer. It...

    I have a Dewalt 735 as a finish planer. It doesn't see rough lumber, and the maximum cut is 1/32". I stone the knives sharp. The factory knives leave a great finish in figured wood.

    Dirty rough...
  22. If the dados are spaced the same distance apart...

    If the dados are spaced the same distance apart as the rollers are, you could end up with no feed traction, assuming the dados are in the surface being planed. Running the wood at an angle would give...
  23. Replies
    18
    Views
    1,134

    Try a sliding table. You can set stops to make...

    Try a sliding table.
    You can set stops to make similarly sized pieces. You can also add in toggle clamps to hold the work down.

    A good use for a table saw miter fence is to get another one, and...
  24. Replies
    7
    Views
    774

    13 second Video show creation of freezer fridge...

    13 second Video show creation of freezer fridge space opening up, kind of like making a "Great Room" in your fridge.

    https://www.youtube.com/watch?v=McgtLUO0IBE
  25. Here's a photo. The motor is a little smaller...

    Here's a photo. The motor is a little smaller than what you're talking about. The pipe shoots the dust into a trailer.
    I never used the bags.

    454135
Results 1 to 25 of 237
Page 1 of 10 1 2 3 4