Search:

Type: Posts; User: tim walker; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    34
    Views
    2,563

    Favorite Cyanoacrylate (CA) Super Glue

    What are your recommendations? I have found that some, in the past, are bad about plugging the nozzle so any that you have experienced in that regard get a go to the front of the line pass. Thanks
  2. Replies
    5
    Views
    2,180

    Thanks, looks like conventional rails which is...

    Thanks, looks like conventional rails which is what I have but on a Bosch. Mine is also a compound beveled so I have to take that into account. How far out does your table extend to account for the...
  3. Replies
    12
    Views
    2,780

    Tom, how deep are those drawers? Mine will be...

    Tom, how deep are those drawers? Mine will be 24" deep w full extension, soft close slides.
  4. Sketchup Question - Multiple Pages or views

    I have Sketchup Pro 2022. Way more than I need but that is what I have. I am drawing some cabinet drawers of varying heights and want to have each drawer height on a different page or tab so that...
  5. Replies
    3
    Views
    543

    Optimalon Cut List Software

    I have used the software previously and it does a good job, but all the work was with 3/4" stock. Has anyone used it on a combo 3/4" and 1/2" ply design or do I need to generate two different cut...
  6. Replies
    3
    Views
    1,166

    Thanks Jim, 1/2" 12 mm it is.

    Thanks Jim, 1/2" 12 mm it is.
  7. Replies
    3
    Views
    1,166

    Drawers (Again)

    Is 1/2" drawer carcass with 3/8 or 1/2" bottoms good for drawers that are medium duty service, 29" wide and 26" deep? 3/4 ply is $49/sheet and 1/2" is $27.89 at my local distributor(Dakota...
  8. Replies
    12
    Views
    2,780

    Inside dimensions will be 32.5" tall (changeable)...

    Inside dimensions will be 32.5" tall (changeable) and 30" wide. Side mount self-closing drawer slides at 1/2" thickness each, so the outside dimension of the drawer will be 29" and the slides are...
  9. Replies
    12
    Views
    2,780

    Drawer Height Sizing

    I am building some shop cabinets that will be 30" wide, so with side mount slides, each drawer will be 29" wide. I will alter install overlay drawer fronts as there will be no face frame. I want...
  10. Acceptable base and stretcer locations?

    Shop cabinet. The cabinet will have about 5 drawers. Intuitively my engineering degree says place base so that it supports the weight from the drawers. The stretchers would be inside the sides at...
  11. Replies
    20
    Views
    1,585

    CabinetSense no longer works with older versions,...

    CabinetSense no longer works with older versions, only 2019-23. I have 2023 hard drive version and it is available for download. Here is the screen capture. 514839
  12. Replies
    6
    Views
    1,014

    Good idea on teh wood pieces Zachary. I 'll try...

    Good idea on teh wood pieces Zachary. I 'll try that methodology first.
  13. Replies
    6
    Views
    1,014

    Cabinet Heights

    Shop cabinets for a miter saw station. Is 38" too high for the counter top? 3" toe kick, 33" cabinet box. 1.5" top. I am 6'6" tall and the distance from the floor to my forearm bent at 90 degrees...
  14. Replies
    27
    Views
    2,312

    Forgot Pocket hole Screws (with or without glue)

    Forgot Pocket hole Screws (with or without glue)
  15. Replies
    27
    Views
    2,312

    Another drawer construction question - Building...

    Another drawer construction question - Building preferences = Butt joint with glue and screws, dados with G&S, Dominos with G&S, or a 45° Lock Miter Router with glue? TIA
  16. Replies
    27
    Views
    2,312

    For lighter drawers(or drawers that may only have...

    For lighter drawers(or drawers that may only have screwdrivers or pliers, is it ok to to just use a rabbit and 1/4" ply screwed and glued to the bottom or would you still use a dado unglued?
  17. Replies
    27
    Views
    2,312

    Mike, how deep are your drawers and what bottoms...

    Mike, how deep are your drawers and what bottoms did you use, 1/4 or 1/2"
  18. Replies
    11
    Views
    726

    Good questiona s tat is the actual cutting area.

    Good questiona s tat is the actual cutting area.
  19. Replies
    27
    Views
    2,312

    Cabinet Drawer Question

    I am building a couple of side-by-side cabinets for the shop. They will be 30" wide. The space between the top and bottom inside will measure 34". Should I make all the drawers the same thickness...
  20. Replies
    11
    Views
    726

    Acceptable SawStopTS Fence RunOut

    I am doing some maintenance and fine-tuning. I have a 3 hp SawStop PCS with a 52" rail system. What is the acceptable runout tolerance for the T Fence? Mine is currently registering 0.005" toe...
  21. Replies
    2
    Views
    898

    Shop Cabinet Question

    About to start building base cabinets for the workshop. Will use a separate base and level that, then install cabinets on top. The cabinets will be all drawers, no doors, and approximately 30" wide....
  22. Another Miter Saw Station Question - Max cut angle

    My Bosch 4410 Dul Bevel SCMS cuts a max of 52 deg right and 60 degrees left. The 4410 is an older saw that has rails in the back so it requires significant space behind the saw. I am building a...
  23. Replies
    8
    Views
    2,701

    Yes I agree on the metric. The last project I...

    Yes I agree on the metric. The last project I did was in metric. it is SO much easier, for instance, if I need to divide 17 13/15 by three. its much easier to divide 454 mm by 3 for151.3 mm or...
  24. Replies
    8
    Views
    2,701

    Plan Drawing on Sketchup using 3/4" ply

    Designing a shop project using 3/4" ply which is really 18 mm (0.708"). When using Sketchup for your design, do you use 0.708" or do you use 0.750"? These cabinets will span approximately 12 ft.
  25. Replies
    19
    Views
    2,657

    So for shop cabinets, toe kicks or no toe kicks? ...

    So for shop cabinets, toe kicks or no toe kicks? I am building a variation of Jay Bates miter station and he did not have toe kicks but then he only had 9” of flat countertop available so that may...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4