Search:

Type: Posts; User: Lee Schierer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.77 seconds.

  1. Replies
    6
    Views
    206

    How thick is the brass coin slot piece? If you...

    How thick is the brass coin slot piece? If you stack several together and make a thicker piece, I think you can make a template with the inlay router bit set. I drew the bit and bushings in cad. ...
  2. Replies
    2
    Views
    97

    Look for some that have non-marring rubber wheels...

    Look for some that have non-marring rubber wheels.
  3. Is this a round table or a rectangular one?

    Is this a round table or a rectangular one?
  4. According to Mr. Google: HDPE pipes and PEX pipes...

    According to Mr. Google: HDPE pipes and PEX pipes are generally the best choices for an underground water line. These durable pipes are resistant to corrosion and rusting, ideal for running an...
  5. Replies
    16
    Views
    318

    As Jim said those are a product that had a...

    As Jim said those are a product that had a relatively short life. They were made to be drop in ceiling panels for a grid system. They have a vinyl layer on one side and insulation on the other. ...
  6. Replies
    7
    Views
    422

    Now that's a hand saw

    While looking for places to see on a recent trip to Northern California to see the redwoods, I ran across this photo.
    466865
    That crosscut saw has to be every bit of 20 feet long. I'd have to get...
  7. When I crosscut a bevel on the end of a board, I...

    When I crosscut a bevel on the end of a board, I cut it on the left side of my left tilting saw. Since the piece is under control of the crosscut guide and not trapped by any fence there is no...
  8. Replies
    2
    Views
    241

    How to call the UK from the US Dial the...

    How to call the UK from the US

    Dial the exit code 011. This will let your carrier know you're making an international call.
    Dial 44, the UK country code. This tells your carrier you're...
  9. Replies
    2
    Views
    356

    I know of nothing other than an accidental...

    I know of nothing other than an accidental deletion by you that could have caused this. Have you checked with the various correspondents to see if they have the old messages? If they send you a...
  10. Replies
    4
    Views
    353

    I've found that some mice can lick the peanut...

    I've found that some mice can lick the peanut butter off the victor traps as well so I lash a piece of old tee shirt to the trigger and mash the peanut butter into that. I find that I can catch 3-4...
  11. Replies
    11
    Views
    794

    The chain is called sash chain and it is...

    The chain is called sash chain and it is available from a couple of sources.
  12. Replies
    1
    Views
    231

    The amount of span depends upon the flatness of...

    The amount of span depends upon the flatness of the supporting floor and the weight to be placed into the cabinet. In your design of two sets of 30" drawers, all the load in the drawers will be...
  13. So about how much did all that cost?

    So about how much did all that cost?
  14. Awesome, don't forget to refresh the lube on...

    Awesome, don't forget to refresh the lube on those shafts raise/lower and tilt shafts once in a while.
  15. There should be some slight play in the shaft...

    There should be some slight play in the shaft back and forth at that casting, just enough so it spins freely. Once you get it working set a reminder on your phone a year from then to lube those...
  16. Replies
    7
    Views
    712

    Very nice project. Getting an office organized...

    Very nice project. Getting an office organized is a really nice project. When I built the desk for our office I put the scanner in a drawer where it is out of the way, but can be pulled out and...
  17. There is a locking collar on the shaft on the...

    There is a locking collar on the shaft on the opposite side of of the casting from the worm gear. That collar should have a fiber washer between it and the casting. Lubricate the shaft, and both...
  18. When I tuned up my Craftsman TS I encountered the...

    When I tuned up my Craftsman TS I encountered the same problem with the adjustment moving back as I tightened the bolts. The lock washers had indented the cast iron just enough that they would pull...
  19. Unfortunately building codes are the minimum...

    Unfortunately building codes are the minimum standard and often don't require the best technology. Ridge vents and soffit vents are pretty inexpensive and greatly reduce the likely hood of ice dams....
  20. Replies
    27
    Views
    1,107

    I have three side sliding windows in my home that...

    I have three side sliding windows in my home that were made by Great Lakes Windows that both sides of the window can slide. They still offer that type of window.
  21. Replies
    10
    Views
    626

    You need to do just one more step not mentioned...

    You need to do just one more step not mentioned above. Lubricate the brass screw threads by scraping the threads over a chunk of beeswax and mash the flacks into the threads with your warm fingers. ...
  22. Replies
    4
    Views
    534

    The jig is pretty simple. I used a piece of scrap...

    The jig is pretty simple. I used a piece of scrap pine. Tilted the band saw table to 10 degrees an ripped off a strip such that one edge tapered to zero.
    466378466379
    I marked lines on the end...
  23. In my experience beeswax doesn't develop a glossy...

    In my experience beeswax doesn't develop a glossy surface appearance.
  24. Replies
    7
    Views
    868

    I agree, a round tenon cutter.

    I agree, a round tenon cutter.
  25. Replies
    4
    Views
    534

    Not a major project, but fun

    I was looking for something simple to make for the two kids next door and my youngest two grand kids. What I decided to try was a hand launched flying toy. I've seen these toys before, but had...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4