Search:

Type: Posts; User: Prashun Patel; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.65 seconds.

  1. How would you do a rip, Tom?

    How would you do a rip, Tom?
  2. Replies
    6
    Views
    159

    Is it that the shoulder line is not straight or...

    Is it that the shoulder line is not straight or that the tenon is not pulled tight enough?
  3. Replies
    6
    Views
    167

    https://sawmillcreek.org/showthread.php?273653-HVL...

    https://sawmillcreek.org/showthread.php?273653-HVLP-3m-PPS-1-0-vs-2-0-Accuspray-opinions&highlight=16124

    Read this. I almost ordered the wrong stuff also about 2 years ago when i was...
  4. Replies
    6
    Views
    167

    I do not know if the version 2 works with the Ho...

    I do not know if the version 2 works with the Ho cup. I bought the original version pps cup system and it has worked well. I liked it so much I bought the small and large cup systems. I can pm...
  5. Replies
    6
    Views
    167

    For what itís worth, you can use the pps system...

    For what itís worth, you can use the pps system with the siphon gun. You just need to order the H.O. Pressure cup. I in fact have the same exact help as u and did this. Worked great.
  6. If it were me, I'd do 12 on the trunk and the...

    If it were me, I'd do 12 on the trunk and the branches, and reduce to the tool port size as close to the tool as is convenient.
  7. Replies
    5
    Views
    154

    I have also rubbed out EM6000. I used 3m rubbing...

    I have also rubbed out EM6000. I used 3m rubbing and polishing compound. Works fine.
  8. Replies
    14
    Views
    549

    I think you should mount your router to a sheet...

    I think you should mount your router to a sheet of plywood with a 2x4 fence. It will work. You can make a ton of projects with this set up. Eventually, you will WANT - not NEED - the...
  9. Replies
    20
    Views
    1,095

    Aesthetics notwithstanding, the important thing...

    Aesthetics notwithstanding, the important thing is to look at the grain on the side of the tenon. If all faces have no run out - as they should, it won't make much difference in the strength. The...
  10. Replies
    11
    Views
    519

    You sound like a lucky man. My kids are teens...

    You sound like a lucky man. My kids are teens too, so I appreciate how wonderful this might be.
  11. Replies
    11
    Views
    519

    Not sure what impresses me more: your taking...

    Not sure what impresses me more: your taking time to do a ppt on screw driving, or your kids willingness to read and do it.

    Take advantage of their interest and your patience. It'll pay...
  12. Replies
    30
    Views
    4,027

    It took me a year to make this. 11 months of...

    It took me a year to make this. 11 months of hemming and hawing through indecisiveness and design, and 1 month to actually make it. These days thatís how it goes.
  13. I wouldn't add ANY mineral oil to beeswax. If...

    I wouldn't add ANY mineral oil to beeswax.

    If anything, I would add in small amounts of mineral spirits to make the wax more pliable. Mineral oil doesn't dry fast enough for me.
  14. You are good to wonder about this. While it can...

    You are good to wonder about this. While it can be done, there are limitations. If the piece is too tall or too long, it's very difficult to hold it properly through the cut - even with a jig. ...
  15. Replies
    26
    Views
    1,918

    I have a wixey. I love it. Yes itís...

    I have a wixey. I love it. Yes itís accurate. Itís small, magnetic, couldnít be simpler to use.
  16. Waterlox original sealer finish. Any wiping...

    Waterlox original sealer finish. Any wiping varnish like this will do the job, but Waterlox is darker than most and I find it appealing on darker woods. Arm r seal is another great one.

    You can...
  17. Replies
    6
    Views
    327

    I agree that itís a hard ask. I made a guitar...

    I agree that itís a hard ask. I made a guitar from a redwood slab and it is just a brittle wood. Imho you are best to round over the edges and eliminate any sharp edges.
  18. Pix of my experiment. Before 455594 ...

    Pix of my experiment.

    Before
    455594

    Initial:
    455595

    After 6 hours (not 8...)
  19. Your coffee test really floored me because by now...

    Your coffee test really floored me because by now that test board should have been cured right?
  20. John, I have spilled a few coffees on my island...

    John, I have spilled a few coffees on my island and never had an issue. After your post yesterday, I ran the same test you did - coffee ring left for 8 hours on the em8000cv with cross linker. I...
  21. Replies
    27
    Views
    1,220

    I donít know how you will be able to glue up...

    I donít know how you will be able to glue up individual blocks perfectly; every single block in each row has to be exactly the same size. I agree that they are usually more easily done by gluing...
  22. Thread: Mirka

    by Prashun Patel
    Replies
    29
    Views
    1,478

    go to 2sand.com It's under:...

    go to 2sand.com

    It's under:
    mirka-5-abranet-pad-protector-qty-5

    These look slightly diff from yours but this is what I bought. Price was good too.
  23. Thread: Mirka

    by Prashun Patel
    Replies
    29
    Views
    1,478

    I have the Porter Cable version of this hose: ...

    I have the Porter Cable version of this hose:

    POWERTEC 70175 Dust Collection Hose with Fittings Plus Two Reducers

    The end of my hose threads right into the CEROS adapter.
  24. Replies
    6
    Views
    469

    Show a picture, can you Ed? Before you get to...

    Show a picture, can you Ed?

    Before you get to messing with extenders or flow or pressure, let's see what you are dealing with.

    Aligatoring is usually due to surface issues (contamination on the...
  25. Thread: Mirka

    by Prashun Patel
    Replies
    29
    Views
    1,478

    Hmm, not at all for me. I've been using mine for...

    Hmm, not at all for me. I've been using mine for > 4 years. No issues with dust collection whatsoever. If the holes are aligned there is zero diff.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4