Search:

Type: Posts; User: Frank Drackman; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    577

    I would measure the thickness of the piece that...

    I would measure the thickness of the piece that you want to put the profile on. Next get a round over bit, with bearing, that is 1/2 of the thickness. Since you can't use a router table use a...
  2. Replies
    9
    Views
    426

    I wasn't kidding at all. I knew that I was...

    I wasn't kidding at all. I knew that I was missing something with the price. That is why I asked.
  3. Replies
    9
    Views
    426

    I forgot about the vacuum system. That is a big...

    I forgot about the vacuum system. That is a big add-on.
  4. Replies
    9
    Views
    426

    $32K used 2018. What am I missing? Same model...

    $32K used 2018. What am I missing? Same model with ATC is $36,795 new at the Shop Sabre site.
  5. I have an extra Dewalt 12" compound miter saw & a...

    I have an extra Dewalt 12" compound miter saw & a Bosch jobsite tablesaw on mobile stands that I keep just to loan out. I can't count the number of decks, stairs, etc that have been built with them....
  6. I asked this question a few months ago and many...

    I asked this question a few months ago and many memebers responded that they did without any issues.
  7. Replies
    7
    Views
    256

    I tried the upside down trick with zero luck. ...

    I tried the upside down trick with zero luck. The saw is over twenty years old and this is the first issue so I'm fine with replacing the switch.
  8. Replies
    7
    Views
    256

    Exactly. It was the first thing that I tried but...

    Exactly. It was the first thing that I tried but was concerned about breaking it. The more I investigated I realized that it had to be the clip so I applied a little more force and it popped right...
  9. Replies
    7
    Views
    256

    Please disregard.I found how to remove from...

    Please disregard.I found how to remove from housing.
  10. Replies
    7
    Views
    256

    Help Removing Switch From Housing

    The switch on my Laguna LT18 bandsaw finally died. I tried blowing it out without any success. I ordered a new part but need some help replacing it. Attached is a picture of the switch in the...
  11. Replies
    15
    Views
    768

    If you want the cherry to age to a darker color...

    If you want the cherry to age to a darker color make sure that your clear coat doesn't have UV inhibitor in the formula.
  12. The Ereplacement website says that it is...

    The Ereplacement website says that it is compatible with your unit. See attached screen shot.

    424653
  13. I installed the vortex cone upgrade kit on my...

    I installed the vortex cone upgrade kit on my dust collector one week ago and I'm extremely impressed. My system started as a 3hp Penn State Industries two bag collector that I swapped the bags for a...
  14. Replies
    5
    Views
    432

    If you are going to color the wood I would...

    If you are going to color the wood I would investigate dyes instead of stains. I find the dyes give me much more control of the color especially in end grain.
  15. Replies
    12
    Views
    421

    I have a different brand. The best way I have...

    I have a different brand. The best way I have found to make sure that the drum is parallel is to use two 1-2-3 setup blocks with no sandpaper attached. The 2" works best for me. One on the inboard...
  16. Replies
    17
    Views
    1,016

    I also have a Dewalt 708 & would not trade it for...

    I also have a Dewalt 708 & would not trade it for anything that I have seen. I'm amazed how long it stays accurate. I use a Forrest Chopmaster and get a great, accurate cut.
  17. Replies
    19
    Views
    1,130

    What kind of companies did you work for?

    What kind of companies did you work for?
  18. Replies
    46
    Views
    2,109

    I like the weight and precision of floor models. ...

    I like the weight and precision of floor models. I have a Jet with the three pulley design. I always change the pulleys to the required speed before drilling. I find that it takes almost no time...
  19. Picture of what was delivered. 423256

    Picture of what was delivered.

    423256
  20. Target Coatings Excellent Customer Service

    I received a shipment today from Target Coatings that was destroyed in transit. It was two quarts of product that both were opened. The shipper simply put what was left of the cans into a plastic...
  21. Replies
    10
    Views
    735

    Wow, thanks Dave. I guess it is back to the...

    Wow, thanks Dave. I guess it is back to the branding irons for me.
  22. Replies
    84
    Views
    4,652

    I use my router on my Dewalt track much more...

    I use my router on my Dewalt track much more frequently than I use the saw. I know that Festool & Dewalt offer adapter plates that ride on the track and attach to the router. I expect that other...
  23. Replies
    10
    Views
    735

    Thank you Kenneth. What are your plans for it?

    Thank you Kenneth. What are your plans for it?
  24. Replies
    10
    Views
    735

    Thanks Kevin. I like your attitude I'm not...

    Thanks Kevin. I like your attitude

    I'm not worried about the money. My concern is the fustration of the time & energy of trying use a tool in a way that was never intended.

    I was hoping that...
  25. Replies
    15
    Views
    815

    They are major upgrades to a fairly inexpensive...

    They are major upgrades to a fairly inexpensive tablesaw. I would rather spend my money on a higher quality saw with no accessories.

    I feel for the OP as I made a similar mistake with my first...
Results 1 to 25 of 236
Page 1 of 10 1 2 3 4