Search:

Type: Posts; User: Steve Mawson; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.25 seconds.

  1. Replies
    3
    Views
    639

    Hi Tony, Send me a email at...

    Hi Tony,
    Send me a email at stevemawson@outlook.com and we can make arrangements.
  2. Replies
    3
    Views
    639

    D-Way 3/8" Beading Tool

    I have a beading tool from D-Way that I do not use so perhaps someone else could use it. Used very little but did a great job when I did use it. Sharpened a very few times. Lets say $40.00 shipped...
  3. Replies
    6
    Views
    594

    I have used the 19s for years and it works well. ...

    I have used the 19s for years and it works well. I prefer the signiture to not take up too much room on the piece. Hard to control depth that the pen tip goes into the wood with the 9, at least for...
  4. Replies
    17
    Views
    1,913

    I build one very much like this and it works...

    I build one very much like this and it works quite well. I use a 1/2" square bar with a carbide cutter. Couldn't have had more than $15.00 in it less the cutter.
  5. Replies
    9
    Views
    1,198

    Glad to see that this whole project was very...

    Glad to see that this whole project was very worhwile. Pretty amazing, the whole process. Now ever better to use.
  6. Free Sanding Drum for 12" Woodmaster Planer

    I have a sanding drum for a Woodmaster 612 planer that I will never use. No cost if you will pay the shipping. Probably weights in the 10-15 lb. range. I am in the 68516 zip code. I came with the...
  7. Replies
    15
    Views
    2,091

    Does look like Elm to me as well. Wish I could...

    Does look like Elm to me as well. Wish I could describe the smell because it is unique.
  8. Replies
    9
    Views
    2,257

    Sorry got busy with other stuff but after some...

    Sorry got busy with other stuff but after some off and on with the collector it now starts without any issues. I did check all the wiring which was all #12 and switched to another unused 20A ...
  9. Replies
    9
    Views
    2,257

    Grizzly G0860 Dust Collector

    This might need to be someplace else but know lots of turners have a dust collector. Need some help on a Grizzly G0860 1 1/5 HP dust collector. It was delivered last Friday and I get it set up over...
  10. Replies
    5
    Views
    980

    My remote switch quit working and it was a loose...

    My remote switch quit working and it was a loose wire.
  11. Replies
    36
    Views
    4,813

    What the other folks have said. There is not any...

    What the other folks have said. There is not any wood that will not vibrate when you get down to 1/2" and 13" long.
  12. Replies
    19
    Views
    2,254

    I almost always give what ever is on the lathe a...

    I almost always give what ever is on the lathe a spin by hand before I turn it on. A good habit to get into to make sure the piece will not hit the tool rest, not spinning too fast, spindle lock not...
  13. Replies
    4
    Views
    828

    Well at least you look to have the same thickness...

    Well at least you look to have the same thickness down the side of the bowl:D. For me seems to happen more with natural edge knocking off some of the bark:mad:
  14. Replies
    11
    Views
    1,093

    Probably finish as is especially if the worm...

    Probably finish as is especially if the worm holes do not go all the way to the inside. How about the dimensions?
  15. Replies
    10
    Views
    1,533

    Bob that turned out quite well. Always good to...

    Bob that turned out quite well. Always good to define the texture area as you have demonstrated.
  16. Replies
    11
    Views
    1,401

    Well I had fun starting the day learning about...

    Well I had fun starting the day learning about batons although I have made one with no knowledge of what I was doing. On the juniper over the years I have found that danish oil with lacquer over it...
  17. Formica works much better if it is sanded down to...

    Formica works much better if it is sanded down to .015-.020 thickness, sand off the surface that has the pattern on it. If left at the thickness of the countertop material it's hard to get hot...
  18. Replies
    3
    Views
    1,149

    Been doing this for years with a standard PVC...

    Been doing this for years with a standard PVC fitting, works fine. Get the closed cell foam at Hobby Lobby
  19. Replies
    21
    Views
    2,891

    When I saw Jimmy Clews demo he said take it off...

    When I saw Jimmy Clews demo he said take it off and use it for the barby. Mine is not attached to the lathe.
  20. It was on display at AAW in KC in June

    It was on display at AAW in KC in June
  21. Replies
    37
    Views
    4,252

    My wife and I have been watching. I got drafted...

    My wife and I have been watching. I got drafted in 1967 however I was sent to South Korea when the spy ship Pueblo was captured by North Korea. Because of that I missed serving in Vietnam although...
  22. Replies
    10
    Views
    1,835

    Great timber, that kind does not come along every...

    Great timber, that kind does not come along every day.
  23. Replies
    9
    Views
    1,478

    Way to go, wish you were just a little closer. ...

    Way to go, wish you were just a little closer. Pretty big deal, especially if it is the first time for something like this.
  24. Replies
    10
    Views
    1,957

    Our church has installed a columbarium, urns from...

    Our church has installed a columbarium, urns from the manufacturer are 5.5x5.5x7 or 212 cu. in. The manufacturer assures me that this volume will hold cremains of the vast majority of folks. ...
  25. Replies
    21
    Views
    3,735

    Tom at JT is having some health issues and having...

    Tom at JT is having some health issues and having a slow recovery. I am positive he will make good on any orders as soon as he is able. Since he is a one man operation it will take him a little...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4