Search:

Type: Posts; User: Mike Tagge; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    34
    Views
    4,609

    Shaper snipe troubleshoot

    I’ve been working on some cabinet door parts and putting them through my power feed on the shaper along with the Aigner 4 wheel device. I have the outfeed fence parallel to the deepest cut on the...
  2. Replies
    6
    Views
    1,558

    Used both, Kem Aqua is thicker base than target...

    Used both, Kem Aqua is thicker base than target but better build. You might need at least a 4 stage system to agonize. My 2 stage could atomize target but not much thicker. My sw store brings in Kem...
  3. Replies
    12
    Views
    1,597

    I ordered mine with it but to change to the dado...

    I ordered mine with it but to change to the dado stack I have a different bushing to use that Felder supplied. The main saw blade bushing comes off leaving a long axle protruding then a flatter one...
  4. Replies
    20
    Views
    2,618

    Probably some sort of CNC machine or hired help....

    Probably some sort of CNC machine or hired help. If I was doing this (and perhaps you already do this) I would gang dado everything and optimize it on full sheets or broken down sheets anyway. Run...
  5. Replies
    8
    Views
    1,842

    Maybe try to pop it with shellac. Any WB finish...

    Maybe try to pop it with shellac. Any WB finish should go over that and not yellow. Also maybe try Target sealer and a WB topcoat. Good results with that too.
  6. Replies
    12
    Views
    1,597

    I guess it depends on what you do. I use my...

    I guess it depends on what you do. I use my Felder dado stack / groover to do all kinds of dados and rabbets for cabinets. Very nice job with absolutely flat bottoms by design. Not sure if you got...
  7. Replies
    12
    Views
    1,234

    Robert - Still having a bit of trouble trying to...

    Robert - Still having a bit of trouble trying to follow exactly what you are doing. I'll take a stab at a solution using what I think you are doing and then if I'm off, hopefully you can figure out...
  8. Replies
    12
    Views
    1,234

    The link looks like adjustment versus install....

    The link looks like adjustment versus install. Which hinges did you use?

    Mike Tagge
  9. Replies
    3
    Views
    2,780

    Tormek Japanese stone?

    I just received my new set of Japanese chisels. I have a t8, and am looking at whether a set of wet stones or the sj250 Japanese stone should be my next purchase. It seems from a quick review that a...
  10. If Rangate is too short, give Greg a call. I was...

    If Rangate is too short, give Greg a call. I was looking into longer bits a while ago before I had a part machined that brought the table into a workable distance. Greg seemed to be able to get...
  11. Replies
    12
    Views
    1,644

    Bevel a large tabletop

    I saw a picture of a conference table that was probably 10' long, 5' wide and 1.5" thick. I imagine that would probably be about 200 lbs or more and very unwieldy to cut on say a table saw or even a...
  12. Loved my Infinity dadonator when I had that saw.

    Loved my Infinity dadonator when I had that saw.
  13. Replies
    8
    Views
    1,348

    Flat tooth? Felder has one - I have the rip blade...

    Flat tooth? Felder has one - I have the rip blade with a flat tooth grind. I'm sure you can look at CMT too.
  14. Replies
    17
    Views
    2,523

    I run into this often for long box shelves. I use...

    I run into this often for long box shelves. I use solid hardwood for the front and glue up thicknesses of plywood for the center. For long load bearing surfaces I would do a half lap style. From...
  15. Replies
    10
    Views
    4,211

    I have the CF741SP. I sold all my individual...

    I have the CF741SP. I sold all my individual tools and moved to a smaller space and also upgraded each one to an industrial level at the same time. I got pretty much every option available on it...
  16. Replies
    14
    Views
    2,922

    I just sanded my live edge walnut slab using an...

    I just sanded my live edge walnut slab using an angle grinder with holey galahad wheel by king arthur tools. Knocked the bark off with a hammer and chopped the stubborn stuff off with a chisel and...
  17. Replies
    17
    Views
    2,762

    Yeah, you are better served buying straight wood...

    Yeah, you are better served buying straight wood to begin with. Warped wood will fight you all the way. For big doors on paint grade, I usually only fake it because of warping issues ( or charge...
  18. Replies
    18
    Views
    2,858

    I did about 50 inset doors in the past year. I...

    I did about 50 inset doors in the past year. I started out making some big mistakes by making doors separately in a production step to the size and then finding out that the face frames were not...
  19. Replies
    3
    Views
    843

    Yes, it is for dining room chairs. I would...

    Yes, it is for dining room chairs. I would appreciate seeing what you did on yours. How did you do the attachments to the stretcher underneath the seat and to the back rail?
  20. Replies
    3
    Views
    843

    Arm rest attachment details

    Hi all,

    I’m currently working on a chair project and have just to add arm rests and finish. However, I’m a bit at a loss for how to attach the arm rests to the frame. I’m thinking of using mortise...
  21. Replies
    4
    Views
    991

    Thanks Gary. I never heard of them but just...

    Thanks Gary. I never heard of them but just reached out.

    Mike
  22. Replies
    4
    Views
    991

    Looking for CNC owner near Chicago

    Hi Creekers,

    I'm working on a table and chairs project currently. However, the scooped seats I think are best suited for a CNC machine. Looking for one in the Chicago area that might be able to be...
  23. Replies
    47
    Views
    7,419

    I've been in "business" for about 3 years now....

    I've been in "business" for about 3 years now. I've done about 1 project a month, although I don't do kitchens. I find this line is not my niche as my work is based less on production and more on...
  24. Replies
    15
    Views
    3,908

    Rod, where did you get your blades rebored?...

    Rod, where did you get your blades rebored? That's one of my sensitive subjects currently with my extensive blade collection :)
    Currently, the build stands at:
    CF741 SP with 2800mm table...
  25. Replies
    15
    Views
    3,908

    Mike, thanks for the tips. Space is my...

    Mike, thanks for the tips.

    Space is my limiting factor here. I'm moving to a smaller space and need to have the capabilities that the CF741 has. I currently have all separates, albeit most are...
Results 1 to 25 of 42
Page 1 of 2 1 2