Search:

Type: Posts; User: Rick Potter; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.28 seconds.

  1. Replies
    11
    Views
    371

    The model A in my garage is two tone tan. Sorry...

    The model A in my garage is two tone tan. Sorry Lowell. They called one of them Copra Drab.
  2. Replies
    19
    Views
    1,036

    The cabinet I described above is currently under...

    The cabinet I described above is currently under the right side of a SS with a 36" fence. There is enough room to use the handwheel on the saw. A bit awkward, but ok for the few times I move the...
  3. Replies
    19
    Views
    1,036

    I have a blade cabinet under the side table. It...

    I have a blade cabinet under the side table. It is about the size of a 2 drawer file cab. It is short enough that it has casters under it for movability, and wide enough to hold 12" blades. The...
  4. Replies
    1
    Views
    340

    Thanks Lowell, I especially liked the part where...

    Thanks Lowell, I especially liked the part where the scofflaw who drove through a funeral procession was fined two chickens and some feed, and plopped them down on the courtroom table. That part of...
  5. Replies
    13
    Views
    644

    I used to go, years ago, to wood turners club...

    I used to go, years ago, to wood turners club meetings held in a steel shop in Norco. It was miserable hot in the summer, and cold in the winter. Noisy too. I heard he later installed spray in...
  6. Mine was certainly structural. Sorry Bill, I...

    Mine was certainly structural.

    Sorry Bill, I don't remember what it cost, but it was not cheap.
  7. Replies
    5
    Views
    380

    Like Eric said. Belt sander worked fine for me.

    Like Eric said. Belt sander worked fine for me.
  8. Just finishing a new garage addition built that...

    Just finishing a new garage addition built that way. I wanted as much height as I could get for possible future car lift.

    Garage is 22'Wide and 32' long, with the ridge beam being 23' or so long...
  9. I will give you a couple examples. I was a...

    I will give you a couple examples. I was a fireman for a large metro department for 34 years.

    There was a large structure fire in a phone company building, where it turned out there were...
  10. Replies
    10
    Views
    610

    I did have one of Freuds Black coated crosscut...

    I did have one of Freuds Black coated crosscut blades on my RAS 20 years or more ago. My wife needed to cut something, and mistakenly thought my steel carpenters square was part of the saw.

    She...
  11. Replies
    10
    Views
    610

    As someone mentioned above, it looks like a Freud...

    As someone mentioned above, it looks like a Freud rip blade. They did use a black coating years ago, before going red.

    Looks like it was used heavily, I would ask the blade sharpener to check it...
  12. Replies
    9
    Views
    481

    Very nice work John. You have given me some...

    Very nice work John.

    You have given me some great ideas to incorporate in mine (CU300) when I finally get to it. Love the extension strut.

    First thing for me though is making a zero clearance...
  13. I made wooden cradles for my 8" pipe, and used...

    I made wooden cradles for my 8" pipe, and used roll a holes to fasten to the cradles.
  14. Replies
    8
    Views
    852

    Push sticks Push blocks Long push dowels for...

    Push sticks
    Push blocks
    Long push dowels for getting past guards.
    Jessem hold down rollers.

    Looks like a pattern here.
  15. Replies
    29
    Views
    1,574

    I will only comment on router size. I built my...

    I will only comment on router size. I built my first kitchen on a bench top router table using a PC 690. No lift, simple fence.

    I used a full size panel raising bit and cope/stick set. As I...
  16. If I am seeing it correctly, it looks like you...

    If I am seeing it correctly, it looks like you should overlap more...like 50%, and not go in straight lines.

    I was taught to go in small circles as you go across the board, then overlap it a lot...
  17. Replies
    37
    Views
    2,411

    Thanks Carl. Glad to see someone making...

    Thanks Carl. Glad to see someone making progress. Tonights task for me was to start figuring out how best to store the various fences and other parts while they are not being used.

    My Son in law...
  18. Replies
    37
    Views
    2,411

    FastCap sells a brush like material that is...

    FastCap sells a brush like material that is fastened to a flexible roll. It is peel and stick. I wonder if that would complete your setup, allowing less dust to escape around the blade.

    They...
  19. Replies
    11
    Views
    594

    Hmmm. About the time you were posting this, I...

    Hmmm.

    About the time you were posting this, I was at Goodwill giving away a NIB Logitech universal remote, which I had no use for.

    Sorry
  20. Replies
    15
    Views
    799

    As I remember it, the road near Lancaster was...

    As I remember it, the road near Lancaster was done that way partially because there were so many accidents on it. It is a desert road, which has a lot of traffic and speeders, connecting two major...
  21. I have bought at least three of the scrunchy...

    I have bought at least three of the scrunchy type, or more accurately....my wife did.

    The first one lasted one day, and the next morning we discovered the dog found it appetizing.

    Second one...
  22. Replies
    37
    Views
    1,654

    Thanks, Jim Good info, as I did not know it...

    Thanks, Jim


    Good info, as I did not know it was for the phone only, and not the computer. They installed it in a ridiculous location, behind some large shelving units, and when they wanted to...
  23. Replies
    37
    Views
    1,654

    I am in the same situation as the OP. We have...

    I am in the same situation as the OP. We have Fios for internet and phone, no TV. My adult grand daughter just ordered that Nighthawk to replace the Verizon/Frontier router, and we have been trying...
  24. Replies
    22
    Views
    705

    Can't speak for Carl, but I need to make an...

    Can't speak for Carl, but I need to make an insert for my MM 300CU Smart because every time I trim off a narrow strip, it goes right down the blade opening just like it was sucked down...which of...
  25. Thread: shop cart

    by Rick Potter
    Replies
    31
    Views
    1,903

    I will be 77 in a couple weeks, have lots of...

    I will be 77 in a couple weeks, have lots of injuries, and I need all the help I can get. I just ordered one. It just about did me in putting a sheet of melamine on the saw by myself a couple days...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4