Search:

Type: Posts; User: Tom M King; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    34
    Views
    894

    False lower face rail actually part of drawer...

    False lower face rail actually part of drawer bottoms, and one drawer instead of two, as it appears. Bottom rail becomes pull. It could still have a divider between the two drawer sections for...
  2. Replies
    28
    Views
    543

    My hard drive "reader" is just a cord with...

    My hard drive "reader" is just a cord with different types of plugs on it. The hard drive doesn't need to be in a case. They just sit on the desk, and even can stack multiples.
  3. Replies
    28
    Views
    543

    You can get a hard drive reader pretty cheap from...

    You can get a hard drive reader pretty cheap from Newegg. It plugs into the drive, and a port on your computer. Then just copy what folders you want onto the new hard drive. Notice what interface...
  4. Replies
    12
    Views
    398

    My current drivers license is good through my...

    My current drivers license is good through my 73rd birthday without glasses. I hope my eyes will be able to pass next time too. So far, so good. In my younger years, I was always ever so slightly...
  5. Replies
    11
    Views
    457

    For a lot of oddball things, I find these...

    For a lot of oddball things, I find these polyester backed abrasive sheets to be very handy-not the PSA backed ones. ...
  6. Replies
    8
    Views
    351

    Another vote for Formica.

    Another vote for Formica.
  7. Replies
    16
    Views
    650

    I set my water stones on edge, and sharpen on the...

    I set my water stones on edge, and sharpen on the side (now up) of the stones. That gives the tangs plenty of room to hang down, if needed. The sides of the water stones can be flattened, just like...
  8. Replies
    15
    Views
    464

    When I'm going to finish over pins, I make sure...

    When I'm going to finish over pins, I make sure the gun is shooting them below the surface, and use only stainless steel pins, so I can put a drop of water over them without leaving a rusty spot. ...
  9. Replies
    68
    Views
    8,116

    Nice looking timber framing joinery Scott!!!

    Nice looking timber framing joinery Scott!!!
  10. Thread: Old tool?

    by Tom M King
    Replies
    15
    Views
    733

    I did a Google search for "1/8" pilot chuck key",...

    I did a Google search for "1/8" pilot chuck key", for an example, and a bunch came up.
    https://www.mscdirect.com/product/details/60911518

    I found this one in a similar way. That's a glove size L...
  11. Replies
    11
    Views
    514

    I thought that would be the way it worked out. ...

    I thought that would be the way it worked out. I feel certain that you will be pleased with the new blade.
  12. Replies
    26
    Views
    1,150

    I use an old, metal filing cabinet to keep my...

    I use an old, metal filing cabinet to keep my helmets, face shields, and some other welding stuff in. I'm sure it's not totally insect, and dustproof, but I haven't had any trouble with either. The...
  13. Replies
    11
    Views
    514

    I've had nothing but perfect blades, with perfect...

    I've had nothing but perfect blades, with perfect welds from them. Something probably happened to that band before it was welded, and not necessarily there. I've never had to contact them for any...
  14. Replies
    10
    Views
    676

    I have some of both, but that's all I remember...

    I have some of both, but that's all I remember about them. I do know which saw does what cut the best.
  15. Replies
    17
    Views
    1,058

    I want one of those big'uns with the crank handle...

    I want one of those big'uns with the crank handle feed. I still use a couple of RAS's, with only the same guard shown on the single blades. My outfeed tables in my tablesaws don't have slots in...
  16. Replies
    26
    Views
    1,150

    I have a good one, and one of the 50 buck ones...

    I have a good one, and one of the 50 buck ones from Northern Tool. The cheap one works fine, but does have a smaller window, which doesn't often matter.
  17. Replies
    30
    Views
    1,239

    The few times I've done it, a good, long level...

    The few times I've done it, a good, long level was plenty good enough. If you can straighten two long boards after adjusting a jointer, and they fit together perfectly, that's a good enough test for...
  18. Replies
    54
    Views
    2,317

    I can see where the new format is better for the...

    I can see where the new format is better for the small screen of a phone. From my first purchase with the new system, I can also see that it's a good thing for me that I've never bought anything...
  19. Replies
    54
    Views
    2,317

    I was able to place an order, no problem. The...

    I was able to place an order, no problem. The only issue I had in checkout was that it took about 25 seconds each for the month and year boxes to become ready to accept entries. I may have missed...
  20. Replies
    28
    Views
    1,697

    It seemed obviously dumb, but now, I'm not so...

    It seemed obviously dumb, but now, I'm not so sure. That electric company did not reverse the charge. The lady I talked to there was very rude, and didn't want to bother with it, just like that...
  21. Replies
    12
    Views
    931

    It won't leave here. I keep a Woodmaster CT 1.3...

    It won't leave here. I keep a Woodmaster CT 1.3 on it for resawing. Operates as good as a new one. We made these Cypress shingles with it, running 10,000 lineal feet through it as fast as they...
  22. Replies
    12
    Views
    931

    Johnny, I felt the same way when I bought that...

    Johnny, I felt the same way when I bought that bandsaw from you.
  23. Replies
    68
    Views
    8,116

    There is nothing worth duplicating about that...

    There is nothing worth duplicating about that tooth geometry. I expect it was originally a rip saw.
  24. Replies
    68
    Views
    8,116

    Unless it's just the lighting, it looks like...

    Unless it's just the lighting, it looks like you're going to have to joint it down pretty good anyway, so might as well try something that you want. With big toothed crosscut saws, it's always a...
  25. Replies
    28
    Views
    1,697

    A card doesn't have to be physically stolen to be...

    A card doesn't have to be physically stolen to be stolen. My Wife had the use of hers stolen, we think after using it in a vending machine. It was used for two trips to a Buffalo Wild Wings in NY. ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4