I was watching Ishanti Furniture on youtube . . .and in one of the videos you see him with his sawdust stove. Just an oversized pipe that he puts a second pipe in the middle of, and then loads it up...
Type: Posts; User: Flamone LaChaud; Keyword(s):
I was watching Ishanti Furniture on youtube . . .and in one of the videos you see him with his sawdust stove. Just an oversized pipe that he puts a second pipe in the middle of, and then loads it up...
For my synthetic waterstones, I do the dunk and drip . . .dunk them in the bucket of water, and then have a drip constantly going on them while they are in use. For my natural stones, I do the same...
5k Nainwa super stone . . . but please, back to the regularly scheduled programming.
If you have access to a table saw with a fence that you trust, the straight edge method works like a charm . . . I have one that clamps so there's no need to screw it down, but I get it close, clamp...
Water, because I use it after my waterstones. It will produce a slurry somewhat easily.
I have one of those too . . . does an excellent job as a finishing stone imho.
For the OP, couldn't he perhaps take a block of wood like Derek has in his picture set for the proper bevel angle, epoxy a strip of hdpe on the bottom of the block of wood, cut out a groove that will...
No, and the main reason is that we've had enough mass market furniture that "kinda" worked for what we wanted it for . . . but it didn't last well for the long haul. If I do it, it's exactly what...
I'm going to say depends on external grade. If you're not in a flood zone, or the shop will be at the high point of your property - 10 foot studs should be fine. If you are in a flood zone, or if...
I'm basing this off of my experience with PC watercooling, and usually even the best sealed closed loop system still will have some minimal loss at the pump/reservoir, even if there are zero leaks in...
It's more likely a factor of evaporation out of the system if he's only losing 10 gallons per year from what is probably 100+gallon system. You have to realize that 40% ethylene glycol means that...
My opinion, which is worth exactly how much you are currently paying for it, is that most of the library systems keep what has been being checked out. In my area, you can find woodcarving and...
I've used the Dewalt, and the Kobalt . . . and based on my experience with those - I wound up purchasing the Hitachi 12" version of this saw. If you have a place to "set it and forget it" - it will...
Let's see if I can remember what I put on my list for "things every house/apt needs" toolbox.
1. Wooden handled hammer
2, A pair of slotted screwdrivers (long and short) and a pair of Phillips...
If Concrete meets earth, there will still be moisture migration, even with a very good drain system in place . . . sorry. The only way around it is a vapor barrier under the gravel base before the...
We had a set of Wustoff/Henkels back in the day, up until a house fire took away most of our kitchen. My wife replaced them with a set of Harris Teeter stainless steel knives (our local grocery...
Not to mention that they sponsor what is one of the last Woodworking shows in NC every October, so I have zero qualms about going to them for anything I need (that they sell).
My Dad used this phrase: You know what an Expert is? X - The unknown variable, Spurt - a drip under pressure.
It's a power tool, but exactly a standard one. Husquvarna 371xp w/a 36" bar and ripping chain. Milling is in my immediate future, which will lead to even more woodworking.
Favorite of old - anything made by Reeses . . . but these days it messes with my stomach too much. Favorite of today - White Chocolate Pretzels made by Utz, and I get 3-4 boxes of them at Sam's...
I have saws that have a tapered plate and saws that have no taper in the plate . . . I can't say there's much of a difference in the actual performance of the saw, but then again I haven't felt the...
In my humble but heavily biased opinion - Teeth can be changed, set can be changed, steel (in reference to saws) is steel . . . what causes me to pick up one saw over and over again is how it...
My opinion, which is worth exactly what you're paying for it:
The LV router plane blades are very good, and the basic set is a good start to build around if you do (or plan to do) a lot of...
It would seem to me that the better you are at making, the less you're willing to settle for 'good enough'. At least for me, I wind up being dragg . . . errr . . . accompanying my significant other...
Hi Bruce, and Welcome
1. If the ends haven't been sealed by now, I wouldn't worry about it. If you want to have a better chance of not having checking/cracks, what you can do is once you get...