Search:

Type: Posts; User: derek labian; Keyword(s):

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    670

    I dont see an unusually high amount of chips from...

    I dont see an unusually high amount of chips from my Fs41es. Its by no means clean though. I think the expectation may be too high for collection.
  2. Replies
    241
    Views
    23,570

    How exciting Jim! It looks like your having quiet...

    How exciting Jim! It looks like your having quiet the fun time :)
  3. Replies
    37
    Views
    3,820

    I looked at the same option a few months back. ...

    I looked at the same option a few months back.

    I would say go single phase. In many cases 3ph would be preferable for the reasons already listed. There may be a HP gain too depending on the...
  4. I was also thinking some wheels but that could be...

    I was also thinking some wheels but that could be tricky. You might consider the blum 30 but try adding a counter balance weight on the top back of the drawer to relieve the stress on the...
  5. Replies
    49
    Views
    6,704

    I purchased some slides from WWE as well a couple...

    I purchased some slides from WWE as well a couple of months back. I couldn't find a better supply either and just resigned myself to wait for the product.
  6. Replies
    12
    Views
    1,475

    For full disclosure, no flex pipe is "smooth"...

    For full disclosure, no flex pipe is "smooth" like steel pipe is. The best you can get is mostly smooth with the ribs mostly on the outside. The more rigid the duct, the better performance and less...
  7. Replies
    12
    Views
    1,475

    I was using the same Powertec duct but I was...

    I was using the same Powertec duct but I was loosing too much suction due to its flexibility and ribs. If you have a more powerful DC (than I) though, it's good value.
  8. Replies
    12
    Views
    1,475

    The hoses I listed are smooth inside, ribbed...

    The hoses I listed are smooth inside, ribbed outside.
  9. Replies
    12
    Views
    1,475

    There are a lot of hose options. You should check...

    There are a lot of hose options. You should check out (https://blastgateco.com/Flex-Hose.php) for a good overview of all options available as the datasheets differentiate them well. You can cut down...
  10. Hi Ned, Curious what you eventually did. Did...

    Hi Ned,

    Curious what you eventually did. Did you use the outfeed at all, cut it down, or keep it intact (not sure how that would fit)?
  11. Replies
    65
    Views
    8,164

    Thats a great price IMHO. Wait until the work is...

    Thats a great price IMHO. Wait until the work is do e though for a final update, it would be nice to know if your happy with the final result. :o
  12. GFCI installed..

    GFCI installed..
  13. Interesting regarding

    Interesting regarding <=250v



    In this case, these lights are effectively hardwired (they were hardwired before) and 10’ up. They are dedicated and on a light switch. The plug was just a...
  14. Yeah Tom, I went with something similar. The...

    Yeah Tom, I went with something similar.

    The box in the ceiling is a 3" round box. I was considering the extra complexity with my original idea and found a surface mount octagon box (4") with 3"...
  15. Electrical supply had same basic solutions...

    Electrical supply had same basic solutions suggested above. I'm going to try to fit an outlet in the box. If that doesn't work, I'll use a blank with a punch out and run flex conduit to a surface...
  16. I think this is probably the best thing. These...

    I think this is probably the best thing. These are low wattage LED lights. I can use SOOW 14g and put a plug on it. I think I'll see if I can get that to work.
  17. No they are hanging from strut. I couldn't find a...

    No they are hanging from strut. I couldn't find a cover at the home store that had a 1/2 screw joint for flex duct. I found one but the holes were off as stated.

    I tried this one, but the holes...
  18. Round Pan ceiling fixture to conduit for drop shop lights

    I previously had surface mounted Florissant lights (quad) that were wired with Romex to a round pan in ceiling plate. I am switching to drop lighting and I've been trying to find a transition from...
  19. Replies
    14
    Views
    896

    I had similar problems, but I found these Bohin...

    I had similar problems, but I found these Bohin pencils to be excellent.

    https://www.amazon.com/gp/product/B004M5BGD4/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
  20. Replies
    9
    Views
    1,379

    My 2 Cents on SS CS in general: There isn't...

    My 2 Cents on SS CS in general: There isn't anything SS customer service can do other than answer the phone, be polite and request the brake to do an analysis, which is what it sounds like they did....
  21. Thank you for the additional details!

    Thank you for the additional details!
  22. Replies
    49
    Views
    4,165

    You might post a picture of the plate to get a...

    You might post a picture of the plate to get a quick/accurate answer if you have it.
  23. Replies
    9
    Views
    1,379

    I tripped a few brakes in short order. It can be...

    I tripped a few brakes in short order. It can be maddening. In the end, i found there were reasonable explanations related to my setup and not a SawStop problem per say. If I was loosing production...
  24. Felder mini-wide belt sander FW 850 classic

    Pretty cool that Felder is making smaller units.

    FW 850 Classic

    1 meter squared of space, 7.5HP. Almost no other details that I could see? I don't even see the width of the belt?

    475354
  25. Replies
    9
    Views
    1,121

    Interesting packaging from Harvey

    I haven't seen a woodworking company use equipment packaging like this before, but I thought it was nice to unpack, and, if necessary, re-pack. It can be broken down and it's easy to store for a bit...
Results 1 to 25 of 458
Page 1 of 19 1 2 3 4