Search:

Type: Posts; User: Kevin Jenness; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.26 seconds.

  1. I used red Loctite once by mistake and was able...

    I used red Loctite once by mistake and was able to weaken the bond with heat. The same goes for most epoxies.
  2. There's this...

    There's this https://www.autogeek.net/griots-orbital-polisher.html# and this...
  3. I've had a Mitutoyo analog model for about 40...

    I've had a Mitutoyo analog model for about 40 years, it still works fine. .001" grads, the dial rotates to set zero. Sorry, don't have a model #. A button tip is more useful for knife setting than a...
  4. From an old thread on customer service...

    From an old thread on customer service https://sawmillcreek.org/showthread.php?235588-What-is-your-experience-with-quot-euro-machine-quot-customer-service...
  5. Replies
    5
    Views
    262

    There are hundreds of resin formulations that can...

    There are hundreds of resin formulations that can be used for this application including polyester, epoxy and polyurethane. For small quantities you are probably best off going to a craft store and...
  6. Replies
    48
    Views
    6,973

    That's about 400 inches/minute, plenty fast for a...

    That's about 400 inches/minute, plenty fast for a machine like that.
  7. At 5.5" I can't see a problem as long as the mc...

    At 5.5" I can't see a problem as long as the mc is the same. Thinner means less potential for issues and more yield. Do both sides for balance.
  8. Be aware that the stated shelf life is one year...

    Be aware that the stated shelf life is one year unopened and eight months after opening. As I recall the same was true for the Weldwood product, although your experience with it indicates that it...
  9. Replies
    5
    Views
    306

    Watch out for splinters and avoid sanding dust....

    Watch out for splinters and avoid sanding dust. Some people are allergic.
  10. Replies
    4
    Views
    229

    There's this (I have not used it)...

    There's this (I have not used it) https://www.systemthree.com/products/cold-cure-cold-weather-epoxy

    A general approach to epoxy in cold temps from West System...
  11. Replies
    18
    Views
    884

    I am definitely considering upgrading my shop...

    I am definitely considering upgrading my shop attire.
  12. The only thing the manual states about the...

    The only thing the manual states about the infeed/outfeed is that the outfeed table is set by the factory precisely and should not be adjusted.

    I checked this several more times with a couple of...
  13. It's not clear what you mean by "sagging" or...

    It's not clear what you mean by "sagging" or exactly what your test procedure is. I am guessing that you are resting your straightedge on the outfeed table and measuring the gap between it and the...
  14. Replies
    15
    Views
    654

    It's hard to know from your description whether...

    It's hard to know from your description whether the problem is inaccurate joints, clamping technique or change in moisture content. A dry run in clamps using a straightedge would tell you a lot. If...
  15. Replies
    18
    Views
    884

    Isn't that something? The best woodworkers have a...

    Isn't that something? The best woodworkers have a way of making it look so easy.
  16. Replies
    5
    Views
    210

    Don't you need a removable dust trap at one end?

    Don't you need a removable dust trap at one end?
  17. Replies
    35
    Views
    3,301

    What is the relative cost of Nordfab pipe and...

    What is the relative cost of Nordfab pipe and fittings to similar gauge spiral pipe? Is there a major decrease in installation time? I recognize the ease of reconfiguration, but is there a good...
  18. I prefer Titebond Extend over original for veneer...

    I prefer Titebond Extend over original for veneer as it has a more rigid glueline. I also use epoxy and Titebond 2 at times. I did use Titebond original on 1/16" veneer on a number of projects with...
  19. Seems as though you could lessen the amount of...

    Seems as though you could lessen the amount of resin used and drying difficulty by roughing the blank first.
  20. Replies
    18
    Views
    1,067

    I guess you could call Phase Perfect products...

    I guess you could call Phase Perfect products "static" in the sense that they don't rely on a rotating coil to generate three phase power, but what is generally referred to as a static phase...
  21. Replies
    18
    Views
    1,067

    Yes, that is true. Ok for lightly loaded motors...

    Yes, that is true. Ok for lightly loaded motors like my 3hp slot mortiser, but it would be self-defeating to run something like a widebelt off a static phase converter.

    It's easy to set up a...
  22. Replies
    4
    Views
    435

    Lee Valley...

    Lee Valley https://www.leevalley.com/en-us/shop/tools/jigs-guides-and-fixtures/76880-veritas-shooting-board-fence?item=05P5485
  23. Clearly the answer is a bigger shop.:) I would...

    Clearly the answer is a bigger shop.:)

    I would definitely keep one of the cabinet saws if possible.

    Go ahead and cut the fence if you must. Keep the offcut in case you move - you can probably...
  24. You can buy commercially made plywood cylinders....

    You can buy commercially made plywood cylinders. For solid wood, glue up staves and turn on a lathe.
  25. From a theoretical standpoint a "true" tenon is...

    From a theoretical standpoint a "true" tenon is rooted in the rail and fully integrated with the surrounding long grain fibers and possibly stronger. As a practical matter a properly sized, fitted...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4