Search:

Started with just a dry fit..
520013
As this frame was labeled as Bottom frame...

Got out the screws, the bottle of glue, a BIG square..and something to drive the screws with...Big Square?...

Side #2 is done..
520009
Drawer runners are done..
520010
Back rails are milled...
520011
And all are assembled with the front rails..to make 9 frames...
520012

So..next time will...

Eric Brown ( on this site) would be the one to talk to about this saw...

I do have the Bishop No.10 version...
520005
That I leave set up for Dovetails..

Been one of THEM days, today....go to type a reply on a website....circuit breaker the Computer is on ( and the House AC Unit) decided to pop...
Decided to kill the time the computer will need to...

So..was a long day...but..
519894
All 9 are done for THIS side...next?
519895
Need to transfer all the layout marks to the case's other side...and mill them..

Wanted to get this out of the...

Set the rip fence to guide the router..
519891
Have to allow for the router's base...including how far in to go..not too bad...?
519892
Got set up to do #8 socket...was running out of a place to...

Tablesaw as a work table/
519887
Works in MY shop...as long as I remember to lower the blade all the way down..

Set up a router, today..
519888
Block is the "backer block" when I milled the...

Ok..yesterday...Had to go and bring the Boss home...(LONG story) THEN go out and pay the monthly bills, and Grocery shop....Then a trip across the street to Lowes..
On Sale!....1 x 2 x 4'....Total...

Ok..got all 18 runners done..
519857
However, came time to cut the pine back rails..
519858
There was only enough GOOD 1x 2 left for 1 back rail....Trip to Lowes yesterday to restock

I had...

Set the router table aside, for now...cut 18 drawer runners on the tablesaw for length..
519848
Here is about half of them....each need a tenon on each end..
519849
Nibble away...working away...

Ok, dovetail bit was done..time to change bits..
519844
There was a time, long ago, where a router by B&D was all metal, and was a clone of a DeWalt No. 610....and both needed 2 wrenches to change...

1st Router table use...needed a jig to slide along the fence..
519835
To run parts past a dovetail bit..
519836
9 "rails", dovetail "Tails" on each end...takes 4 passes

Goal was to match this...

Will do an "Up-Date" later this evening..once we get the Boss back home and settled in...
Warning: Router Table will be in use
Warning: Tablesaw will be making tenons

Weird Sign award: This...

Thinking the term does or does not include slicks?
519786
And maybe not from the realm of Timber Framers?


Shorty is 11" long..and a mere 1-1/2" wide...
Big Brother..is 15" long, and an even...

ok, to get the rebates milled..
519750
Had to move these out of the way...cauls were a might too close to my arms as they were going by..
519751
Used the Craftsman3720 to mill a 3/8" wide by 1/4"...

Curved areas near the feet, used a drum sander in a cordless drill...high rail was lower,,,with a beltsander, and couple spokeshaves..and a palm sander..until finally..
519744
The Stanley No. 80...

Up date time...the 2 sides were clamped together, inside to inside...the back stiles already have their rebates milled to house the 1/4" plywood back. Lined the back stiles up
519741
With the...

Had to replace a curvy one..
519686
Had enough "Leftovers" for that..
519687
The wide one on the bottom..isn't quite that wide, any more

The best 9 rails are all clamped up into a single...

These 2 planks..
519682
Needed to be cross cut in 24" (Roughly) lengths
519683
Then run through the rip fence at 1-3/8" width...
519684
Then needed to skinny them down to 3/4" thickness.....

Side #2 is out of the clamps..
519681
And Standing in front of Side #1...back to back...one foot will need trimmed a bit, otherwise, they match up quite nicely

2 hours and 20 minutes in the shop, today...Results?
519667
Well..there is the inside of Side #2...being glued up..
519668
Had to get 8 raised panels and 9 rails all spiffy-fied up..
519669
And...

Shopping trip..$108.86
Need to load this up..
519606
Into this space..

519607
Needed to fold the other back seat down..so the 8' long 1 x 4s will fit...The six 1 x 2x 6' were a tight...

Well..I did try to get $20 off....but..he only allowed the 10% the Mall gives...on anything over $40...

Cheer Up....Yard Sale Season has started around here...

The Boss is coming home next Wednesday Afternoon-ish...Same day as Pay Day...I get to go out, and pay the bills that morning, then go pick her up. Being released to Home Health Care.

She also...

A dry fit that also involved a panel...
519596
Did not go well...seems I will be doing this, tomorrow...again..
519597
The Dreaded Too Fat Rebate....back has said enough for today...and..
519598...