Search:

Type: Posts; User: Dan Hunkele; Keyword(s):

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    598

    I feel for you. I've lost knives in similar...

    I feel for you. I've lost knives in similar situations. I was given a couple Smith and Wesson spring assisted knives. I'm glad I didn't pay for them because the springs didn't last long before...
  2. Replies
    22
    Views
    1,458

    Walmart has these ...

    Walmart has these

    https://www.walmart.com/ip/The-Write-Dudes-Gorilla-Lead-Edge-Mechanical-Pencil-1-8mm-2-Pack/44933641
  3. Replies
    7
    Views
    654

    https://pbs.twimg.com/profile_images/1130944374261...

    https://pbs.twimg.com/profile_images/1130944374261637120/Ud5L2uT7_400x400.png
  4. Replies
    15
    Views
    1,304

    Wedge forks are used to remove car's tie rod...

    Wedge forks are used to remove car's tie rod ends. Look for one that may be the right size to fit between the live center and the shaft. I have used cold chisels as wedges for this job too.

    ...
  5. Replies
    1,694
    Views
    194,517

    467354 467356

    467354 467356
  6. Replies
    27
    Views
    1,734

    There may be something going on. The Red Maple...

    There may be something going on. The Red Maple trees in this area are the last to lose their leaves and this year their leaves went first. Not just a tree here and there but everyone of them that...
  7. Thread: pewter

    by Dan Hunkele
    Replies
    3
    Views
    1,628

    General Metalworking I goofed in my earlier thread. Pewter is mostly...

    I goofed in my earlier thread. Pewter is mostly tin.
  8. Thread: pewter

    by Dan Hunkele
    Replies
    3
    Views
    1,628

    General Metalworking I have in the past tried to freshen up Pewter...

    I have in the past tried to freshen up Pewter items and found them to be hard to work with. I think if you try to solder it it may have a meltdown. 50-50 solder is 50% tin and 50% lead and melts...
  9. I have heard of this before but I would have to...

    I have heard of this before but I would have to wait and see how the Winter weather went to be able to tell which end is the head.
  10. Replies
    11
    Views
    1,655

    Live in Ohio now but grew up in Pittsburgh, Pa. ...

    Live in Ohio now but grew up in Pittsburgh, Pa. We called them Monkey Ball trees. The fruit are said to be good for keeping spiders and other insects away. Put them around the basement floor. ...
  11. Replies
    182
    Views
    35,974

    Policeman Wins One! A motorcycle police...

    Policeman Wins One!


    A motorcycle police officer stops a driver for shooting through a red light. The driver is a real jerk, steps out of his car and comes striding toward the officer, demanding...
  12. Replies
    2
    Views
    766

    I bought a lightly used Grizzly G0657 on...

    I bought a lightly used Grizzly G0657 on Craigslist a few years ago for $150.00.
  13. Replies
    3
    Views
    626

    It is a two speed drill and the swivel...

    It is a two speed drill and the swivel holds/locks the red drive gear in the hole. Remove the red drive gear and insert it in the other hole and the speed is changed.
  14. Replies
    11
    Views
    1,102

    In my neck of the woods they figure $1500 a day...

    In my neck of the woods they figure $1500 a day for a tree cutting crew. Lost all my ash trees 4 or 5 years ago. I have been doting on some small ash trees that have sprung up. I wonder if the...
  15. Replies
    9
    Views
    1,325

    Hand screw clamps employ screws with both right...

    Hand screw clamps employ screws with both right and left handed threads. Might be a good replacement if proper length and thread size could be found.

    Also, may it have come from a buffing system?...
  16. Replies
    16
    Views
    1,454

    Never any fun that's for sure. Happened here a...

    Never any fun that's for sure. Happened here a few years back. A shed which doesn't have electricity run to it took the hit and had the siding blown off one side. Traveled to the next shed and...
  17. Replies
    41
    Views
    3,541

    When I get a cramp at night I get up and eat a...

    When I get a cramp at night I get up and eat a teaspoon of yellow mustard. Not sure why it works but it does. Supposed to be old home remedy.
  18. Replies
    16
    Views
    1,494

    I use the Inogen. I bought it on Ebay. They...

    I use the Inogen. I bought it on Ebay. They were plentiful and cheap until Covid-19 took hold. Mine works well and I get about 4 hours run time on the larger battery at the 3 liter setting. I...
  19. Replies
    9
    Views
    1,436

    I agree with John, using a solvent will dissolve...

    I agree with John, using a solvent will dissolve the glue and it will definitely infuse some of it into the wood which may affect the finish.
  20. Replies
    8
    Views
    1,421

    I agree, there are lots of good videos on...

    I agree, there are lots of good videos on machining. I've watched many Tubal Cain videos and like to watch Joe Pieczynski and This Old Tony also.
  21. Replies
    8
    Views
    1,421

    I have a tail stock on my metal lathe that can be...

    I have a tail stock on my metal lathe that can be moved side to side out of alignment with the head stock. Then with a drive dog and turned between centers a taper can be achieved.
  22. Fork lifts use batteries and chargers. Give a...

    Fork lifts use batteries and chargers. Give a local dealer a call. They never seem to turn down a job.
  23. Replies
    182
    Views
    35,974

    I was a very happy man. My wonderful Italian...

    I was a very happy man. My wonderful Italian girlfriend and I had been dating for over a year, and so we decided to get married.

    There was only one little thing bothering me....It was her...
  24. Replies
    6
    Views
    633

    Heavy and balanced weight makes them great for...

    Heavy and balanced weight makes them great for turning spin tops on the lathe.

    458389
  25. Replies
    34
    Views
    2,601

    https://www.cpcprint.com.au/app/uploads/2020/01/17...

    https://www.cpcprint.com.au/app/uploads/2020/01/1793-030-No-Smoking-400.png
Results 1 to 25 of 181
Page 1 of 8 1 2 3 4