Search:

Type: Posts; User: George Yetka; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    17
    Views
    751

    If you are ever looking for bigger they offer the...

    If you are ever looking for bigger they offer the journeyman upgrade
  2. My first try with Rubio after a month or so I...

    My first try with Rubio after a month or so I started noticing the end grain actually pulling a little in. This went on in 2 coats as there were a few spots that looked dry after it dried. I had used...
  3. Replies
    17
    Views
    751

    I got a shipping notification last night the...

    I got a shipping notification last night the final piece was shipped and will be delivered thursday. Im taking off Friday.

    I got x50 journeyman with the mounting frame, Wall mount, 80mm spindle...
  4. Replies
    4
    Views
    407

    I believe once theres a hit on the record the...

    I believe once theres a hit on the record the insurance becomes very expensive, even cost prohibitive.

    I dont like how expensive the end of life stuff can be with animals. I know plenty of people...
  5. Replies
    18
    Views
    1,522

    If the tool comes not on a pallet, you can assume...

    If the tool comes not on a pallet, you can assume it has been forked before.
  6. Replies
    67
    Views
    3,734

    I thought the next move is NJ, then maybe...

    I thought the next move is NJ, then maybe PA/NC/SC/FL. You have to slowly transition to rural life out of the city
  7. Replies
    4
    Views
    714

    You can convert it. I have one vented outside,...

    You can convert it.

    I have one vented outside, this is a monster DC at a great value
  8. Thread: Offcuts

    by George Yetka
    Replies
    16
    Views
    1,105

    I have a hard time throwing away tiny pieces of...

    I have a hard time throwing away tiny pieces of BB. let alone hardwood. I find projects to use it all up.
  9. Replies
    2
    Views
    478

    I think your overplanning. I have only ever...

    I think your overplanning. I have only ever single coated polyx and got great results. Mostly coasters and charcuterie boards. Sanded to 220, cleaned with mineral spirits. Apply with white pad and...
  10. Replies
    4
    Views
    574

    What are they made out of? I like raw Ply for...

    What are they made out of? I like raw Ply for shop cabinets.
  11. Replies
    54
    Views
    2,840

    Perhaps a second house, with a second car, and a...

    Perhaps a second house, with a second car, and a second watch. We'll show those bastards.

    Im actually down to watches, stove, and microwave. Everything else is automatic. Watches don't bother me...
  12. Replies
    19
    Views
    1,352

    I would layout your equipment on paper and figure...

    I would layout your equipment on paper and figure out makes sense for that. Once you know where the machines will be run power to those spots. Figure on possibly rewiring at some point. Be able to...
  13. Replies
    24
    Views
    1,282

    OSHA doesnt allow for cord repair. You can swap...

    OSHA doesnt allow for cord repair. You can swap the whole thing but I dont have a guy in the shop and Im a union shop so my guys cost me too much to spend the time diagnosing and repairing it. I get...
  14. What are you planning on using it for? A...

    What are you planning on using it for?

    A couple i would start with are 1/4 &1/8 down cut bits, 1/4 and 1/8 compression bits, bowl bit, v-bit, and a surfacing bit.

    That will get you going. down...
  15. Replies
    24
    Views
    1,282

    Blades being equal the expensive one will get...

    Blades being equal the expensive one will get through your material faster. I do not like the quick disconnect. the older keyed ones were nicer if you could hold onto the key. I have purchased 6 a...
  16. Replies
    5
    Views
    350

    Sorry about your friend. I think theres a good...

    Sorry about your friend. I think theres a good portion of us here that do it for fun and dont care how much we lose along the way. I was selling cutting boards at a $10 profit because I like making...
  17. Replies
    22
    Views
    1,458

    .5 is good against a straight edge with light...

    .5 is good against a straight edge with light pressure. .7 or .9 is better if it in a tool like some of woodpeckers where you drag the pencil. Smaller the better for accuracy
  18. Replies
    20
    Views
    938

    I here that wiring through the switch is not...

    I here that wiring through the switch is not ideal because if the outlet goes bad you lose both. I wouldnt think this is a problem as I would change it anyway and have plenty of spares in the house....
  19. Replies
    72
    Views
    5,796

    Miniaturization. Thats the future for humanity :)...

    Miniaturization. Thats the future for humanity :)

    If we came up with free power that has no downside or cost to the environment, figured out to recycle 100%, limit 2 kids then sterilize we may...
  20. The fence isnt something I noticed as an issue...

    The fence isnt something I noticed as an issue until after my first day of milling. It seems like the right side is more solid but as you move to the left it gets flimsier. I think if you could put...
  21. Replies
    40
    Views
    1,675

    That hole doesnt look natural. That isnt the...

    That hole doesnt look natural.

    That isnt the prettiest spot. But a fernco coupling as others have mentioned may work. You can get a product like this...
  22. Replies
    13
    Views
    863

    I started on the festool ets ec. After a while I...

    I started on the festool ets ec. After a while I saw a deal on the mirka if I bought overseas it came with 5&6" pads, 200 sheets of Abranet paper, and a vacuum hose. For 550 or so. I then rewired it...
  23. A3-31 here the planer function has been dead on...

    A3-31 here the planer function has been dead on with the exception boards started sticking and I couldn't figure out why. I was about to take it apart and re-calibrate but someone said lube the bed....
  24. Replies
    8
    Views
    951

    About how long will they take to dry? And what...

    About how long will they take to dry? And what percent ends up getting lost(overridden with bugs/rot/etc) I always think I wanna try this but scare myself off with thinking it will take too long and...
  25. Replies
    16
    Views
    1,473

    Make a router flattening setup for it

    Make a router flattening setup for it
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4