Search:

Type: Posts; User: glenn bradley; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.55 seconds; generated 56 minute(s) ago.

  1. Very true Kevin. The routers I had like that I...

    Very true Kevin. The routers I had like that I quickly realized I had to convert them to counterbore if I wanted to do accurate template routing with them. Easily done if you happen to love a...
  2. For one or two a 1" tall piece of scrap with a...

    For one or two a 1" tall piece of scrap with a slot cut into it clamped in position could do ya ;)
  3. As JKJ suggests; maybe some reinforcement? ...

    As JKJ suggests; maybe some reinforcement?

    469328
  4. Let me see if I did a thread on that . . . Nope. ...

    Let me see if I did a thread on that . . . Nope. It is pretty much from ShopNotes #116. Basically you need a platform that will clamp to your bandsaw (or your bandsaw fence if the bandsaw is big...
  5. Shop Made Template Collar Router Base Plates

    I was surprised that with all the router stuff I have around that I did not have a pair of medium sized router base plates with template profiles in them.

    ...
  6. Replies
    10
    Views
    514

    Tubes show up on the used market now and again so...

    Tubes show up on the used market now and again so keep an eye out there. A longer tube will be less expensive than a whole new fence setup unless there are other reasons to forklift your current...
  7. +1. Used plane prices have gotten a bit high...

    +1. Used plane prices have gotten a bit high right now but, persistent searching can still land you a deal. You may put in a bit of work to assure the sides and sole are a good 90 degrees to each...
  8. There is enough spring in the hose but it can...

    There is enough spring in the hose but it can still fight you a bit. On my recent re-install I made the hose short enough so that it stretched out a bit when the lid was fastened down on the drum. ...
  9. Replies
    9
    Views
    460

    I was trying to make Shop Made "Blokkz" and this...

    I was trying to make Shop Made "Blokkz" and this is what I came up with. I'm sure I picked up the general idea somewhere along the way; I'm not that clever ;-)
  10. I just bought a little hose from Grizzly for my...

    I just bought a little hose from Grizzly for my new install of my old G0440.

    469231

    The idea of a platform with casters on it would work as well.
  11. Replies
    9
    Views
    563

    469201 123789456890123789

    469201

    123789456890123789
  12. Replies
    6
    Views
    400

    If I understand correctly that you will fill the...

    If I understand correctly that you will fill the entire rectangle, floating panels with complimentary characteristics can do a lot for a blank space.

    469168469167469169
  13. Replies
    10
    Views
    735

    +1 on Woodpecker products and the folks at...

    +1 on Woodpecker products and the folks at Carbide Processors. Thanks for posting the review. I have the original PRLs and they have worked flawlessly for many years. I also have their old...
  14. Replies
    9
    Views
    460

    Thanks guys. Baby steps right now. Next will be...

    Thanks guys. Baby steps right now. Next will be some boxes or small wall cabinets I think. By summer I should be ready to start on the bedroom set, the sideboard, the kitchen island, various...
  15. Replies
    9
    Views
    460

    Three 8x10 Frames

    I am still just getting warmed up after a 2 year hiatus so I am doing some small items to wake up my muscle memory https://www.woodtalkonline.com/uploads/emoticons/default_unsure.png.

    ...
  16. Replies
    7
    Views
    326

    Another heavy shellac user here that doesn't feel...

    Another heavy shellac user here that doesn't feel confident that that is shellac. It is easy enough to test. Put some 90+% alcohol on a cotton ball and hold it against the surface for 30 seconds or...
  17. I sprayed drywall primer with my Earlex 2 stage...

    I sprayed drywall primer with my Earlex 2 stage and a 2.0 needle. I just thinned it till the Ford cup said it was good and it sprayed without issue. If you cannot thin, look at renting an airless...
  18. A variation on my Shorts Tower may help(?) ...

    A variation on my Shorts Tower may help(?)

    469046 . 469045
  19. Agree that it's funny. I think Brian was...

    Agree that it's funny. I think Brian was actually trying to help. He may just be unaware that there really is no "Delta" support for older Delta tools at this time. :)
  20. Replies
    24
    Views
    1,317

    I’m sure either would work fine. I have boards...

    I’m sure either would work fine. I have boards that are used regularly that are many years old all made with Titebond three. No failures. This includes and green boards, edge green boards, and inlay...
  21. Replies
    24
    Views
    1,254

    I agree with those stating that a sled carries...

    I agree with those stating that a sled carries the off cut away from the blade and eliminates the problem. An alternative to this is something like the Grr-ripper which carries the off cut away from...
  22. Replies
    10
    Views
    497

    +1. Very well thought out and I should think...

    +1. Very well thought out and I should think easily modified if the need arises.
  23. Replies
    41
    Views
    3,592

    I was re-reading some of this thread and had...

    I was re-reading some of this thread and had missed Russel's reference to the JET 98-0060 Tuftool. I rarely have trouble with the Supermax 19-38 clip but was curious. Using the pictures in the...
  24. Replies
    2
    Views
    737

    Frame Miter Clamping Helper

    I thought I posted this way-back-when under one of my "Random Tips" rambles I get on now and then but cannot find it. This was just going to be a "hey I made some more of these" thread but just in...
  25. Definitely one of my favorites. They’re...

    Definitely one of my favorites.


    They’re hitting the ground like wet sacks of cement.


    Classic.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4