Search:

Type: Posts; User: Davis Young; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    18
    Views
    1,048

    He needs to run a frame the same thickness as the...

    He needs to run a frame the same thickness as the battens along the perimeter of the metal. Screw the frame into the metal. Then pocket hole the battens to the frame and attach the show boards to the...
  2. The 50-284 extension would be for a 52Ē Unifence....

    The 50-284 extension would be for a 52Ē Unifence. The 50-285 extension would be for a 30Ē Unifence.
  3. Six would be correct.

    Six would be correct.
  4. Replies
    1
    Views
    336

    They already tried to get discontinue it once...

    They already tried to get discontinue it once before but Steve Base at the Festool training school convinced them that a lot of trim carpenters use them when scribing moldings and cabinets. It really...
  5. Replies
    28
    Views
    2,595

    Itís a little spendy but I love my Metabo paint...

    Itís a little spendy but I love my Metabo paint remover. It uses carbide inserts like those found in a helical cutterhead. Dust collection is pretty good too.
  6. My preference is to avoid slotted screws at all...

    My preference is to avoid slotted screws at all cost. But if you foresee using counterbored slotted screws, then get the cabinetmaker tips.
  7. Replies
    8
    Views
    827

    I have no suggestion on the order, but you can...

    I have no suggestion on the order, but you can time yourself on a dry fit (including the time to ďapplyĒ glue) to see how much you can do given the open time. If itís not enough time, you can glue as...
  8. My favorite blade is still the stock blade that...

    My favorite blade is still the stock blade that came with my Unisaw, and I have a Forrest WWII. I believe it was made for Delta in New Zealand, 10Ēx50 ATB&R.
  9. Replies
    15
    Views
    1,294

    Conventional knobs will require a hole drilled...

    Conventional knobs will require a hole drilled 2-3/8" or 2-3/4" from the edge of the door, so 5 to 5-1/2" wide stiles work well. You want to keep the stile wide enough so the knob isn't too "crowded"...
  10. Replies
    15
    Views
    1,294

    Panel thickness will depend on how much of a...

    Panel thickness will depend on how much of a rabbet you want to reveal between the rail/stile and the panel. Typical interior doors are 1-3/8" thick so a 1/4" panel will yield a 9/16" rabbet on...
  11. Replies
    13
    Views
    1,042

    Keep in mind the Domino is going to be about as...

    Keep in mind the Domino is going to be about as efficient as itís going to get. Just like with a biscuit joiner, there really isnít anywhere for the chips to go but through the port. Their sanders...
  12. Replies
    10
    Views
    1,085

    I have a lot of the systems: Festool/Tanos,...

    I have a lot of the systems: Festool/Tanos, Makita interlocking (which is a clone of the old style Festool/Tanos), Bosch L-Boxx, DeWalt Tough System and DeWalt T-stak (and the Craftsman version...
  13. Replies
    3
    Views
    670

    I have the 22-580 and I like it a lot. I donít...

    I have the 22-580 and I like it a lot. I donít have access to my machine right now so I canít take the hood off to check until probably later in the week. The plastic dust hood for it is still...
  14. Replies
    20
    Views
    1,975

    With the European style saws, like others have...

    With the European style saws, like others have said, lay it down on its spine and then strap down in a pickup truck. I did this all the time with the Agazzaniís. Back the saw up to the open bed and...
  15. Replies
    10
    Views
    1,113

    For the record, they do not fit. I have both the...

    For the record, they do not fit. I have both the Makita and Festool system. The Makita rail has an extra ďrabbetĒ on the outer extrusion that prevents the Festool parallel guides from sliding on.
  16. Iíve encountered base mouldins that captured the...

    Iíve encountered base mouldins that captured the plaster wall above so removing the base was a no go. I also prefer not to have a shoe base. Perhaps a biscuit joiner could do the job. The Eluís body...
  17. Replies
    7
    Views
    978

    I live less than 30 minutes away from a McMaster...

    I live less than 30 minutes away from a McMaster Carr center so I usually order will call. I have often clicked the submit order button and then immediately driven over there. I have yet to beat...
  18. Replies
    8
    Views
    777

    Same for me as well.

    Same for me as well.
  19. Thatís my setup and it is totally doable. Keep in...

    Thatís my setup and it is totally doable. Keep in mind without the vacuum, youíre going to get quite a bit of dust on your track and plywood. Rigging up a dust bag to the port did contain a...
  20. Replies
    11
    Views
    1,525

    I've done this when the Festool Planex first came...

    I've done this when the Festool Planex first came out and I tried it out on a workbench. The bench was reasonably flat but had accumulated a bit of dirt as well a thin surface finish. It just wasn't...
  21. Replies
    18
    Views
    2,399

    The 104-1/4Ē was probably for the Inca 710 for...

    The 104-1/4Ē was probably for the Inca 710 for any Canadian owners out there.
  22. Replies
    20
    Views
    2,030

    Do like those hanging shoe racks. Get some thin...

    Do like those hanging shoe racks. Get some thin strips of metal and bend a hook on one end to fit over the top of the door. Then drill some holes to mount the rack.
  23. Replies
    22
    Views
    1,910

    For stainless steel nails, if you have trouble...

    For stainless steel nails, if you have trouble sourcing them locally, I would recommend fastenerusa in Modesto. They carry the 316 stainless nails in all the gauges for saltwater application.
  24. Rockler and Lee Valley sells washers for the rare...

    Rockler and Lee Valley sells washers for the rare earth magnets. Basically a metal disc with a countersunk hole in the middle for a screw. Gives it a clean look.
  25. Replies
    5
    Views
    3,185

    Good information Peter. I have the manual if...

    Good information Peter. I have the manual if anybody was still interested in getting a copy. Love the router and it's still going strong.
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4