Search:

Type: Posts; User: Joe. Rivera; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    1,759

    with such a purty top, I'd go with a maple board.

    with such a purty top, I'd go with a maple board.
  2. Replies
    3
    Views
    1,219

    Looks like a good score to me.

    Looks like a good score to me.
  3. Replies
    18
    Views
    3,747

    Generally it depends on how/where the drawers...

    Generally it depends on how/where the drawers slide. The sides can be lower if you have drawer slides glides holding the drawer level when it's pulled out. Other wise, it will have to be a tight fit...
  4. Replies
    12
    Views
    2,069

    Normally, I use small cork dots in residential. ...

    Normally, I use small cork dots in residential. Those look more like a commercial type.
  5. Replies
    7
    Views
    1,401

    Very cool!

    Very cool!
  6. Replies
    9
    Views
    1,246

    That project needs a very hard wood. other...

    That project needs a very hard wood.
    other wise when you grind something in it, it will also grind the wood, adding wood dust to the food.

    Olive can be ordered from a supplier, dont choke on...
  7. If you can get to it, the attic. Either in the...

    If you can get to it, the attic. Either in the house or the garage if it has a ceiling lid, or even open rafters you can lay them out on. Works great.
  8. Replies
    36
    Views
    5,605

    did you have a contract with him? if not, tell...

    did you have a contract with him?
    if not, tell him to pound sand. if he shows up, call the sheriff.
  9. Replies
    7
    Views
    1,219

    I would think any good quality blade would cut...

    I would think any good quality blade would cut it. But, as you remember, It will dull them fairly quick compared to other woods. What would you expect from wood that lasts 100+ years buried in the...
  10. you're using the speedy channel line set cover ?...

    you're using the speedy channel line set cover ? I'd go with Silkaflex to seal the penetration hole

    377720
  11. Replies
    19
    Views
    12,196

    I'd go with some wire cross ties. From under...

    I'd go with some wire cross ties. From under table top to bottom strechers, centered between all the legs.
    LIke two wire "X"s each way
  12. Replies
    16
    Views
    3,699

    Sawzall to the rescue ! Cutt between studs,...

    Sawzall to the rescue !
    Cutt between studs, have fun. If there's a fortune up there, share.
  13. Replies
    9
    Views
    6,785

    Apply a liberal amount of Wipe-On Poly to a...

    Apply a liberal amount of Wipe-On Poly to a clean, soft, lint-free cloth and rub it into the wood.
    Let dry 2-3 hours. Then lightly sand entire surface with fine sandpaper (220 grit) to ensure an...
  14. Replies
    9
    Views
    6,785

    Read the label. Most all I ever used, oil base ,...

    Read the label. Most all I ever used, oil base , wanted you to scuff smooth with steel wool.

    If nothing else, it will take out any nibs and make it really smooth.
    Some water base you can...
  15. Replies
    12
    Views
    1,776

    I just built a downdraft table with 2" 20x24 merv...

    I just built a downdraft table with 2" 20x24 merv 8 filters I get from work. I used an old furnace blower and motor.
    Works pretty good, when the filter are plugged, I just take them out back and...
  16. Replies
    83
    Views
    15,540

    Original Stanley metal case 12' w/schoolbus...

    Original Stanley metal case 12' w/schoolbus yellow tape rule.
  17. Replies
    13
    Views
    2,479

    do you remember "chicken" of the sea Simpson...

    do you remember "chicken" of the sea Simpson ?
  18. Replies
    22
    Views
    3,391

    Correct. Read the ballast and match to the...

    Correct.
    Read the ballast and match to the amount and watt bulbs you have. If your bulbs are in fact 40watt- T8 you'll need a ballast that list 2- F40T8. Then follow the wiring diagram on that...
  19. Replies
    22
    Views
    3,391

      that pic is...

    <p>
    </p>
    <p>
    &nbsp;</p>
    <p>
    that pic is showing a 2 lamp wiring only. There should be a listing on the ballast of what watt bulb, How many, and what T &nbsp;types it can run. Im not clear on...
  20. Replies
    25
    Views
    3,863

    ~ $200 give or take

    ~ $200 give or take
  21. Replies
    4
    Views
    1,605

    The orange ones should be urethane as well . ...

    The orange ones should be urethane as well .
    There is no special way. Take a slice across it with a razor knife and peel off. Clean off any adhesive.( there shouldn't be any)
    put the blues on...
Results 1 to 21 of 21