Search:

Type: Posts; User: Bill George; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.31 seconds.

  1. You do not need to use the entire scene edit as...

    You do not need to use the entire scene edit as needed. Then scale and put on one side of the bar top and same at the other end, I think you can reverse image and have it face the other.
  2. The 10.5 x x version also includes the Photo...

    The 10.5 x x version also includes the Photo Engraving software I think anyway. I am still on 9.5 and upgraded from 8.5 a couple years ago primarily because of the enhanced 3 or 2.5D part. IF you...
  3. With VCarve Pro the full version you can purchase...

    With VCarve Pro the full version you can purchase from related Design and Make just about any 3D scene you can think of and incorporate it into your project. No need to spend 2K for a program to do...
  4. Replies
    19
    Views
    3,339

    Bert watch the video, what he does with a sketch....

    Bert watch the video, what he does with a sketch. If I am not wrong and it seems I have been a lot on here, it will also scan the image and automatically align for you.
  5. Replies
    1
    Views
    848

    I have one, its not your typical eBay Chinese...

    I have one, its not your typical eBay Chinese laser, he designs them and has the machines built. I have had mine for maybe 3 years. Unpacked, set up and it just runs and works. Never have adjusted...
  6. Replies
    40
    Views
    1,791

    I am going to un follow this Thread and let you...

    I am going to un follow this Thread and let you Experts keep on, I suggest you read and learn from the Links I have posted.
  7. Replies
    40
    Views
    1,791

    Over 50 years in the trade, most of which was...

    Over 50 years in the trade, most of which was commercial and industrial side, and design installation of controls. Last 12 years I taught the subject. Do a Google search and educate yourself. Large...
  8. Replies
    40
    Views
    1,791

    [QUOTE=Frank Pratt;3073565] Well larger motors...

    Well larger motors that have a choice of either supply voltage start and run better on 230 volts. I am (was now retired) a licensed master electrician and been so since 1964. I am well aware of how...
  9. Replies
    40
    Views
    1,791

    I downloaded the Owners Manual and it comes...

    I downloaded the Owners Manual and it comes pre-wired for 120 vac with a standard plug to rewire to 230 vac is involved and hoping I can paste here. Motors do not need a neutral just two hot wires...
  10. Replies
    41
    Views
    3,339

    To make things simple and affordable, use a...

    To make things simple and affordable, use a standard CNC controller and software, consumer grade. Just use the Z axis and its done. No reinventing the wheel. For a stepper / servo driver and info...
  11. Replies
    41
    Views
    3,339

    The controller and the control software will give...

    The controller and the control software will give you the position readout, no need for a DRO. A normal CNC would have X,Y, and Z all controlled by the software. Is that what your planning or...
  12. Replies
    16
    Views
    44,892

    Nancy, Its common to start a new Thread instead...

    Nancy, Its common to start a new Thread instead of replying to one 13 years old, and I see moderators say the same thing. Happy Thanksgiving.
  13. Replies
    41
    Views
    3,339

    So is this router table a CNC router?

    So is this router table a CNC router?
  14. Replies
    16
    Views
    44,892

    David perhaps you did not notice but the last...

    David perhaps you did not notice but the last post in this Thread was 13 years ago.
  15. Thread: Dust

    by Bill George
    Replies
    20
    Views
    1,760

    You can put the entire room under negative...

    You can put the entire room under negative pressure with the proper sized exhaust fan. Of course then you need to bring in fresh air make up and dump it close by your main shop area. True it gets...
  16. Just depends on who packs them, the one I got...

    Just depends on who packs them, the one I got from LightObject years ago was surrounded by spray in foam with plastic enclosing the tube.

    www.lightobject.com/Search?CategoryId=14
  17. Replies
    9
    Views
    1,973

    You have the machine, try it yourself? Lots...

    You have the machine, try it yourself? Lots faster than posting a question and waiting for an answer.
  18. Replies
    40
    Views
    1,791

    This is what he posted above "'I've had a SawStop...

    This is what he posted above "'I've had a SawStop Pro 1.75hp 220v saw for approx. 5 years now. From day one it tripped frequently "

    Yes dedicated 120 volt 20 amp plugs are different than...
  19. Replies
    40
    Views
    1,791

    Yes it will. Undersized or long cord would cause...

    Yes it will. Undersized or long cord would cause excessive volt drop on start up. Motors draw 3 - 4 times FL rated current on start up. The breaker or TD fuse Usually has enough time delay built in...
  20. Replies
    40
    Views
    1,791

    Having been in the electrical trade since 1962...

    Having been in the electrical trade since 1962 and retired as a master in 2007 I can safely say I have been around a while. There are electricians who wire houses and I was not one of those. I did...
  21. Have you checked the classifieds here? Lots of...

    Have you checked the classifieds here? Lots of times good machine set for months unsold and I have not a clue why. Local Craigslist, same thing. Bruce has some good advice above, and don't limit...
  22. Thread: Transport

    by Bill George
    Replies
    19
    Views
    1,624

    Look up Lift Gate service or consider CNC Router...

    Look up Lift Gate service or consider CNC Router Parts/ AVID kits. I had a local towing company with a flat bed pick up at freight company and deliver to my house a 1000 lb surface grinder.
  23. Replies
    17
    Views
    812

    Well I have been downsizing and it does not make...

    Well I have been downsizing and it does not make sense for me to get the Shop Smith, its listed on Des Moines, Iowa Craigslist if anyone else is interested. It looks to be all there according to the...
  24. Replies
    17
    Views
    812

    He found the chuck but missing the handle. The...

    He found the chuck but missing the handle. The lathe tools appear to be un-used. He wants $450 for the machine and it appears to be a 1988 model by the S/N.
  25. Replies
    17
    Views
    812

    Ok there is a handle and chuck that needs to be...

    Ok there is a handle and chuck that needs to be located? Is it a common chuck so if its missing one could be purchased?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4