Search:

Type: Posts; User: Lee Schierer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.28 seconds.

  1. Replies
    5
    Views
    283

    I got three calls supposedly from my own home...

    I got three calls supposedly from my own home telephone number on my home line.
  2. Replies
    11
    Views
    299

    I'll sit this one out....

    I'll sit this one out....
  3. Replies
    11
    Views
    299

    Gerald Ford. He was picked by President Nixon to...

    Gerald Ford. He was picked by President Nixon to replace VP Agnew, who had resigned. He became President when Nixon resigned.
  4. Replies
    5
    Views
    277

    Was the blade pulling toward the center of the...

    Was the blade pulling toward the center of the circle or away from it?

    How does your circle jig align to your table?

    Did you try to tension your blade a bit more after it warmed up from making...
  5. Replies
    15
    Views
    400

    Back in the60's or early 70's there was a camera...

    Back in the60's or early 70's there was a camera and process using film that took two images slightly off set from a single camera which could be printed that appeared to be 3 dimensional.
  6. Replies
    4
    Views
    352

    PC-7 will work very well for that repair. You...

    PC-7 will work very well for that repair. You can fill in the gouge so it is a little proud of the surface and shave it down flat with a file or hand plane. Once the gouge is filled, you an also...
  7. Replies
    30
    Views
    1,590

    The problem with using a tooth is many of them...

    The problem with using a tooth is many of them are ground at an angle on the sides so getting the same point of reference is difficult the flat of the blade is a more consistent point of reference. ...
  8. Replies
    11
    Views
    544

    If the bottom is plywood don't worry about...

    If the bottom is plywood don't worry about expansion. Make a dado all the way around on the sides.
  9. Replies
    5
    Views
    590

    Check your pressure switch and on/off switch for...

    Check your pressure switch and on/off switch for dirty contacts.
  10. Replies
    8
    Views
    558

    Yes that pad should extend below the two fence...

    Yes that pad should extend below the two fence faces. As noted above replacing the pad is relatively easy. I also recommend using UHMW.
  11. Replies
    30
    Views
    1,266

    Years ago, my father had a can of stain that was...

    Years ago, my father had a can of stain that was specifically walnut sapwood stain. When applied you could no longer tell the sap wood from the heart wood by color. I've seen some of those stained...
  12. Eric, a good way to avoid shearing screws of any...

    Eric, a good way to avoid shearing screws of any size is to (1) drill pilot holes and (2) lubricate the threads by dragging them across a lump of bees wax. I don't recommend soap because they can...
  13. Both my 2012 Pilot and 2016 Accord have tpms...

    Both my 2012 Pilot and 2016 Accord have tpms sensors in the wheels. Both vehicles have reset instructions in the owners manual. Sometimes it pays to read those books that come with the vehicle.
  14. Replies
    25
    Views
    1,208

    One trick I learned a number of years ago is that...

    One trick I learned a number of years ago is that when you glue up a miter joint, you should apply glue to both sides of the joint. The faces being glued are essentially end grain and as such will...
  15. Replies
    14
    Views
    827

    Powder post beetle holes are almost exactly 1/8"...

    Powder post beetle holes are almost exactly 1/8" in diameter.
  16. Replies
    11
    Views
    716

    The dimple made depends on how hard you press the...

    The dimple made depends on how hard you press the two mating parts together. I find that light pressure works pretty well and leaves a nice center point for a brad point bit. Dowels like biscuits...
  17. Replies
    14
    Views
    789

    S4S lumber generally runs a half inch under the...

    S4S lumber generally runs a half inch under the stated dimension. A 1 x 5 is actually 4-1/2" wide. Rough lumber is usually just at or slightly over the stated width. Once you clean it up you will...
  18. Replies
    11
    Views
    716

    Exactly, they come in different sizes, usually as...

    Exactly, they come in different sizes, usually as a set of two for each size.
  19. Replies
    30
    Views
    1,590

    Although some of your ripping problem may be the...

    Although some of your ripping problem may be the material, if you haven't aligned your saw you need to stop everything and do that now. We would like to think that the saw would come aligned from...
  20. I don't think your well guy knows what he is...

    I don't think your well guy knows what he is talking about. I've had a well with a air control that was working for many years and it never required the tank to be drained to restore the air. That is...
  21. You need to supply more information. How big is...

    You need to supply more information. How big is your tank? Does your pump have one pipe or two going to the well?

    I will say this for sure. If you turned off the power for as long as you said...
  22. I have two similar flashlights and one has a...

    I have two similar flashlights and one has a flakey switch that tends to pop out of place when you open the light to replace the batteries. It stays out of place until you intentionally realign it...
  23. Replies
    1
    Views
    753

    Long piece adjustable taper jig

    I am in the process of adding rigid insulation to a ceiling before putting up drywall. There was already 3-1/2" insulation that was pushed up and stapled in place leaving about a 1" air gap at the...
  24. Replies
    16
    Views
    679

    Here you go....

    Here you go.
  25. Replies
    15
    Views
    866

    The legs I have seen that look like the ones in...

    The legs I have seen that look like the ones in your photo have a cast metal cap at the end of the leg that slips over the wood. Leg Caps
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4