Search:

Type: Posts; User: James Minick; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    22
    Views
    514

    Send me a message with an email address and I'll...

    Send me a message with an email address and I'll email to you.

    Thanks,

    James

    Here it is in a dropbox, The first file is an archive containing the rest.
    ...
  2. Replies
    22
    Views
    514

    There is another way. Make sure your USB cable...

    There is another way.
    Make sure your USB cable is a good one.
    I can send you the driver set that I have that I am using right now.
    I can tell you how to install.

    I need to know your ability...
  3. Replies
    22
    Views
    514

    Here is what I run: 420563420564 Running on...

    Here is what I run:

    420563420564

    Running on 1 physical and 2 virtual machines, all Win 10 64 bit though.
    Something to try maybe?
  4. Replies
    8
    Views
    341

    If you must solder... Remove the screw, Fab a...

    If you must solder... Remove the screw, Fab a piece of wire with a GOOD connector, solder to the screw, replace the screw.
  5. Replies
    22
    Views
    514

    I run 2.14.10 on 64bit Win 10. I installed the...

    I run 2.14.10 on 64bit Win 10.
    I installed the LMCUSB.sys driver set.
    Small enough to email.
    The driver is Intel/AMD specific.
  6. Replies
    8
    Views
    341

    I would use another method. Heat can cause your...

    I would use another method. Heat can cause your tube to shatter or create a weak spot.
    Use a terminal if possible.
    Sorry I didn't get back to you sooner, holiday here.

    James
  7. Replies
    8
    Views
    341

    Should have positive + at one end and negative...

    Should have positive + at one end and negative terminal at the other. You may need to attach one or the other.

    https://ae01.alicdn.com/kf/HTB1NQDUXNv1gK0jSZFFq6z0sXXaK.jpg
  8. I start with a low 50khz freq and 80% power to...

    I start with a low 50khz freq and 80% power to blast away material (I blast carbon build-up). Then use a higher freq 100khz and lower power 50% to finish. Check/adjust focus.
  9. Replies
    9
    Views
    385

    Make sure your grounds are good.

    Make sure your grounds are good.
  10. Replies
    9
    Views
    385

    Here are a couple of pics from my setup......

    Here are a couple of pics from my setup...
    419357419358
  11. Replies
    9
    Views
    385

    I would also like to add that you have an awesome...

    I would also like to add that you have an awesome machine!!!
    Get your "as built" drawing and schematic done as soon as you feel it's right.
    Photo every terminal block, controller connection, DIP...
  12. Replies
    9
    Views
    385

    I'll check some of my notes. When all else...

    I'll check some of my notes.

    When all else fails....

    "Calculatus Eliminatus"
    Dr. Seuss

    You are going in the right direction, keep plugging away Les, you will succeed!
  13. Replies
    9
    Views
    385

    Use voltmeter check voltages at critical points...

    Use voltmeter check voltages at critical points also check when pulsing, look for change.
  14. Replies
    14
    Views
    611

    This is a great place to get MUCH info on what...

    This is a great place to get MUCH info on what you are trying to do.
    Homing or perhaps Origin gets set from the first power-up of the controller.

    Do you have a drawing or schematic of your...
  15. Replies
    14
    Views
    611

    I'm assuming you have followed the steps in the...

    I'm assuming you have followed the steps in the "RDC644XG Controller User Manual"?

    If you are confident enough, smoke test.

    I would check the Lightburn Software forum also for tips.
  16. Replies
    2
    Views
    395

    .......I'm in a great mood, so I'll take one for...

    .......I'm in a great mood, so I'll take one for the group!

    First of all, welcome to the forum!

    There is no easy answer to these questions...
    That being said, there are a number of factors...
  17. I use wired remote to activate the blower on the...

    I use wired remote to activate the blower on the CO2. The wireless controls air, additional blower, and lights.
    $25 for both.417166
  18. The controller in the laser is the dongle. When...

    The controller in the laser is the dongle.
    When not powered up it puts you in "demo" mode.
  19. Replies
    1
    Views
    453

    I have no experience on the Gravo, but the...

    I have no experience on the Gravo, but the physics should apply to all.
    This guy explains well, kinda long but worth watching.
    Make sure you have triple checked yourself for safety, know what you...
  20. Fibre wont touch it, will take a CO2. I tried...

    Fibre wont touch it, will take a CO2. I tried with some beads from a popular craft store, couldn't mark with a 50W Fibre.
  21. Replies
    20
    Views
    1,851

    I'll spill the beans on what I have learned about...

    I'll spill the beans on what I have learned about this...
    USA company with contacts in China arrange for shipments of components to the US packed in the same crate as dog toys, dollar store stuff,...
  22. Replies
    20
    Views
    1,851

    Generally the Raycus Fibre laser source runs...

    Generally the Raycus Fibre laser source runs about $100/Watt, factor that in the equation.

    The frequency range is also an important metric to compare.

    I've seen tuned 20w with a good lens cut...
  23. Replies
    20
    Views
    1,851

    .....Having said all that, I just shredded a gear...

    .....Having said all that, I just shredded a gear on my CO2 laser table. There will be stuff like this that happens with anything.
    You have to be ready to do the DIY aspect.
    The Chinese stuff is...
  24. Replies
    20
    Views
    1,851

    Yes, read the thread. There are companies that...

    Yes, read the thread.
    There are companies that buy China components and stuff cases in the US.
    I have one built in China (100w CO2) with issues on arrival and one built here (50w Raycus fibre) with...
  25. I have one similar to this......

    I have one similar to this...
    https://www.ebay.com/itm/Dia-80mm-Rotary-Attachment-Rotation-Axis-For-Fiber-Laser-Marker/202609273464?hash=item2f2c742a78:g:jIwAAOSwwPtcde7T
    About $500 with...
Results 1 to 25 of 26
Page 1 of 2 1 2