Search:

Type: Posts; User: Edward Weingarden; Keyword(s):

Page 1 of 14 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    14
    Views
    1,328

    I had a Revo 24/36 and had many problems with the...

    I had a Revo 24/36 and had many problems with the headstock, but that's a long story. With respect to problem #2 (lock down bounce back), I found that if I pushed the locking lever down slowly, the...
  2. Replies
    12
    Views
    631

    I don't know what effect water has on CA glue,...

    I don't know what effect water has on CA glue, but you can use a spray chemical activator for immediate setting of the CA.
  3. Replies
    11
    Views
    750

    Thank you.

    Thank you.
  4. Coastal Tools in West Hartford. 510 New Park...

    Coastal Tools in West Hartford.

    510 New Park Ave
    West Hartford, CT
    860 233-8213
  5. Replies
    11
    Views
    750

    Richard: Can you elaborate on what you mean by -...

    Richard:
    Can you elaborate on what you mean by - " By adding the oil you complicated the addition of more water based product".
  6. Replies
    22
    Views
    1,440

    I believe the instructions for Watco D.O. says to...

    I believe the instructions for Watco D.O. says to wait at least 72 hrs after application, before top coating with a polyurethane.
  7. Replies
    11
    Views
    750

    Thanks Prashun. I apply liming wax after the...

    Thanks Prashun. I apply liming wax after the india ink, and remove the excess wax with Danish oil. Thus, I'm somewhat limited in terms of a top coat due to the wax and oil that's been applied.
  8. Replies
    11
    Views
    750

    Thanks for the replies. I think I'll try sanding...

    Thanks for the replies. I think I'll try sanding after applying the india ink, and then a second application of the ink.
  9. Replies
    11
    Views
    750

    India Ink

    I recently ebonized a bowl with Speedball India Ink, which has shellac in it. After it dried, the surface was rough, although I suppose that shouldn't surprise me. I went ahead any applied Watco...
  10. Replies
    12
    Views
    925

    I would suggest researching the process of making...

    I would suggest researching the process of making BLO. The things that I have read say that chemical driers are added during the production process. Some people feel that once any finish has cured,...
  11. Derek - The reason for the bandsaw is that I'll...

    Derek - The reason for the bandsaw is that I'll be cutting curves.

    Blue tape? Are you referring to painter's tape?
  12. Thanks Richard

    Thanks Richard
  13. Thanks for the replies. JKJ - good idea for...

    Thanks for the replies.

    JKJ - good idea for the poster board.
  14. Cutting Plexiglass on the Bandsaw

    Will cutting plexiglass ruin a bandsaw blade? Would it be better to cut it with a jigsaw? Thanks.
  15. Rodger & Tom - thanks for the feedback. I bought...

    Rodger & Tom - thanks for the feedback. I bought two of the long post rests at the Mid Atlantic Symposium yesterday. Seeing your replies today, I was able to return them and order the custom length...
  16. Grizzly G0800 and Robust Tool Rest

    Does anyone know if a Robust tool rest is high enough in the banjo of a Grizzly G0800 lathe? Thanks.
  17. My approach is as follows: For the right side of...

    My approach is as follows:
    For the right side of the V, the skew should be coming in from the right (handle to the right of center). In addition, rotate the handle of the skew slightly clockwise so...
  18. Replies
    4
    Views
    496

    Ditto what Dwight said with respect to the Jet...

    Ditto what Dwight said with respect to the Jet 1642.
  19. Replies
    12
    Views
    801

    Thanks Brice

    Thanks Brice
  20. Replies
    12
    Views
    801

    Brice's picture is what I have. The 3/8" ID hose...

    Brice's picture is what I have. The 3/8" ID hose I use for my vacuum system will slide on to the nipple. I'll try putting a cable tie around the hose end on the nipple.

    Brice - is your push on...
  21. Replies
    12
    Views
    801

    Holdfast Rotary Vacuum Adapter

    I Just received the Holdfast Rotary Vacuum Adapter for my Grizzly G0800 lathe. The quick disconnect on my vacuum hose does not stay on the male end coming off the vacuum adapter. Does anyone know how...
  22. Replies
    14
    Views
    860

    Thanks Dave

    Thanks Dave
  23. Replies
    14
    Views
    860

    Thanks Dave. Btw - what's a salt cellar?

    Thanks Dave. Btw - what's a salt cellar?
  24. Replies
    17
    Views
    1,175

    As you can see from the prior posts, there are a...

    As you can see from the prior posts, there are a number of methods to try to prevent cracking. Here's what I do for my twice turned hollow forms. When I harvest green wood, I always seal the ends...
  25. Replies
    14
    Views
    860

    I've used Watco Danish Oil in the past, but have...

    I've used Watco Danish Oil in the past, but have moved to putting on a coat of Seal Cote Shellac Sanding Sealer, followed by WOP. I find that the WOP builds faster by first using the Seal Cote. Final...
Results 1 to 25 of 343
Page 1 of 14 1 2 3 4