Search:

Type: Posts; User: Mike Hollingsworth; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    31
    Views
    1,006

    Take advantage of the high taxes we pay and vent...

    Take advantage of the high taxes we pay and vent outside.
  2. Bingo!!! Same experience I had when I moved...

    Bingo!!!

    Same experience I had when I moved from a lunchbox planer.
    I can no longer make a kiss pass with soft lumber.
  3. Replies
    17
    Views
    1,105

    Local is important, but in the end I'd go with...

    Local is important, but in the end I'd go with the one that weighed the most.
  4. Behr Paint

    For Inside Wall Paint:
    417050
    This stuff is flat and needs two coats.
    417051
    This stuff is "Matte" and will cover in one coat, but needs to be thicker to cover roller marks due to it's slight...
  5. Replies
    22
    Views
    717

    Sam made a batch from phenolic about ten years...

    Sam made a batch from phenolic about ten years ago. If you can get him to make some again I'm in for a couple more.
  6. Venting Outside is Best Choice I've ever made for...

    Venting Outside is Best Choice I've ever made for the shop
  7. Replies
    19
    Views
    1,318

    Until you try to cut a 45 on a two inch piece of...

    Until you try to cut a 45 on a two inch piece of maple. (essentially a 3 inch cut)
  8. Isn't that a metal bandsaw? If so, it's worth a...

    Isn't that a metal bandsaw? If so, it's worth a lot more.
    Is there a reducer gear on the other side?
  9. I'd wipe it all off with lacquer thinner then...

    I'd wipe it all off with lacquer thinner then reapply the teak oil. Immediately wipe all of it off with a paper towel to leave a thin finish that will probably dry overnight.
  10. Replies
    13
    Views
    1,172

    I rarely see hickory/pecan thicker than 4/4. Any...

    I rarely see hickory/pecan thicker than 4/4. Any thicker takes a long time to dry.
    I suggest looking up a kiln schedule to see if it's even possible to dry it at 3" without cracking.
  11. Replies
    11
    Views
    1,217

    I was going to say $9.

    I was going to say $9.
  12. Replies
    14
    Views
    1,110

    I'm going to bet that an unrestricted 6" has more...

    I'm going to bet that an unrestricted 6" has more flow than 8" through a filter.
    I exhaust outside. Biggest improvement I've ever made.
  13. Replies
    13
    Views
    1,185

    Grizzly offers a single phase 24" model. ...

    Grizzly offers a single phase 24" model.
    Oscillation will keep your belts from burning up, but you'll end up with wavy scratches instead of linear. A platen is the answer to that problem.
  14. Love it. I'll bet it weighs a ton.

    Love it. I'll bet it weighs a ton.
  15. I think the canopy in the photo is visually top...

    I think the canopy in the photo is visually top heavy. reducing height will make it more crown like. My $.02
  16. Replies
    6
    Views
    911

    This is an amazing place

    This is an amazing place
  17. Replies
    17
    Views
    1,090

    I second that

    I second that
  18. Replies
    14
    Views
    1,199

    It's my experience that the really curly stuff...

    It's my experience that the really curly stuff (tiger maple) is the soft kind. I look forward to the more knowledgeable experts confirming this (or not).
  19. Replies
    30
    Views
    2,473

    Many Thanks

    Many Thanks
  20. There's a release under the slider at the back.

    There's a release under the slider at the back.
  21. Run Forest Run

    Run Forest Run
  22. Replies
    20
    Views
    1,212

    I sure wouldn't try gluing all 4 corners at the...

    I sure wouldn't try gluing all 4 corners at the same time.
  23. Replies
    37
    Views
    2,678

    Cut a 1" hole in a board with the brad point bit....

    Cut a 1" hole in a board with the brad point bit. Put it over the hole and use it as a guide.
  24. Replies
    16
    Views
    1,067

    Due to the large sanding face oscillation is not...

    Due to the large sanding face oscillation is not that important. You will wonder how you ever did without this sander.
  25. Replies
    165
    Views
    13,195

    Took me a couple years to realize that router...

    Took me a couple years to realize that router tables (small hole) are cutter up and shapers (giant hole) are cutter down.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4