Search:

Type: Posts; User: David Utterback; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    9
    Views
    506

    I tried make a very light cut with the first pass...

    I tried make a very light cut with the first pass and one of the pieces on the outside of the stack was slightly smaller than the other 3 pieces. The take up roller did not make contact. When I...
  2. Replies
    9
    Views
    506

    It worked fine. Thanks

    It worked fine. Thanks
  3. Replies
    9
    Views
    506

    You've seen my shovel? I made a mistake. It is a...

    You've seen my shovel? I made a mistake. It is a Byrd shelix head. Thanks for the input.
  4. Replies
    9
    Views
    506

    Edge planing with Shelix head

    Responders below have let me know my mistake. Cannot change title, though.

    Is it okay to edge plain thin pieces with a Byrd Shelix head on my DW735? I was planning to gang 4 pieces of 3/8" thick x...
  5. Replies
    19
    Views
    485

    Nice pieces. I love the contrast in colors and...

    Nice pieces. I love the contrast in colors and grain pattern. Thank for sharing.
  6. Replies
    14
    Views
    400

    Very nice work. How did you make the bills on the...

    Very nice work. How did you make the bills on the hummingbirds without breaking them off? Also, how are you able to make the mortises for the bills?

    Thanks for sharing.
  7. Replies
    14
    Views
    363

    Nice work and adaptability in the design. Best...

    Nice work and adaptability in the design. Best wishes for your daughter.
  8. If you are reluctant to do another dowel, you...

    If you are reluctant to do another dowel, you could drive a small nail somewhere on the outer panel inside surface and cut them near the surface. The nails plus the existing dowel with help minimize...
  9. Nice, nice work and great display of the results....

    Nice, nice work and great display of the results. Thanks
  10. Those are very good reasons, Jim. Thanks for...

    Those are very good reasons, Jim. Thanks for sharing your project photos, excellent as always.
  11. Replies
    18
    Views
    920

    Your observation about variance over the length...

    Your observation about variance over the length of the ruler is exactly what I have. Undersized at 1 - 3", variably over between 3 and 10", etc. etc. What I do not understand is why this type of...
  12. Replies
    18
    Views
    920

    The problem is that 5" in the 10 - 15" range is...

    The problem is that 5" in the 10 - 15" range is unequal 5" in the 0 - 5" range. The former is off by about 1/16". What this means is that if I measure an opening in the 10 - 15" range and then set my...
  13. Replies
    18
    Views
    920

    OMG, 30 y/o go-to ruler incorrect

    I know many members have been correct in recommendations to ensure comparability of measuring tools. But, I am just not careful enough.

    But, wow, what an awakening. Using my go-to quick...
  14. I agree that sanding is not needed if the pieces...

    I agree that sanding is not needed if the pieces are clean and nearly flat. I am concerned that squeeze out will be a problem after assembly and that sanding needs will be reduced if it is completely...
  15. It is hard to tell from the photo but it looks...

    It is hard to tell from the photo but it looks like one species is doing most of the sweating. Did you continue to wipe away the excess? I have used a similar mix on crotch walnut without any problem.
  16. They look like future light switch covers :)

    They look like future light switch covers :)
  17. Replies
    30
    Views
    1,211

    Gotta love it. It is beautiful.

    Gotta love it. It is beautiful.
  18. Replies
    31
    Views
    1,796

    Thanks for the post about success with your...

    Thanks for the post about success with your table. Many good suggestions from all on improvements to consider. Your observation of the hose contraction is right on.
  19. Auxiliary TS fence to trim large drawer boxes

    Years ago, I got a great deal on some pre-finished maple dovetailed drawer boxes (half blind at all corners) from a commercial shop in the area. I have used them to build tool storage for the shop...
  20. Replies
    18
    Views
    850

    What are the lighter colored lines between the...

    What are the lighter colored lines between the pieces? They appear uniform except where missing for the defect. You may be able to match the color with your mixture.
  21. Replies
    5
    Views
    535

    Sending you a pm.

    Sending you a pm.
  22. LV currently has free shipping on order >$40.

    LV currently has free shipping on order >$40.
  23. Replies
    25
    Views
    1,932

    Poll: Is that burl wood? Could that explain the lack of...

    Is that burl wood? Could that explain the lack of cracks?
  24. Replies
    25
    Views
    1,932

    Poll: I like cookies. A lot! Just not that texture,...

    I like cookies. A lot! Just not that texture, though.
  25. Replies
    22
    Views
    1,348

    Nice, nice, nice. The shell inclusion looks...

    Nice, nice, nice. The shell inclusion looks perfect.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4